Jump to content
SAU Community

Recommended Posts

Jack at the rear use the diff,

at the front the crossmember as it is one of the stronger points, otherwise use two trolley jacks and under the lower control arms on the front and these are cast and rather strong...

but do NOT put the jack anywhere near the steering rack, sway bar, sump or gear box as the result may cost more than an arm and a leg...

To be quite honest I would use the jack and then place axle stands underneath for more even distribution, remember use the right tool for the right job.

  • Replies 75
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

a tyre shop jacked my r33 up on the front sills. It popped both my front guards out and flattened the ride with the jacking point marks in it. I didnt notice it until a few days later so they wouldnt fix it. I have since noticed alot of skylines with the same, bottom of the front guard popped out slightly.

  • 3 months later...

If you are jacking your car up on a completely flat surface (garage concrete floor) your car isn't going to move anywhere if you have wood/bricks infront & behind the other 3 wheels.

I just use the factory/standard jack points (which of course are damaged).

I also have to drive the front wheels up onto some 4x2 because of my sideskirts being too low.

I use the factory jacking point in the sills to jack up the car, a piece of 6"x4"x2" hardwood with a slot cut in the top (3/4" deep 1/2" wide across the top face) goes between the jacking point and the trolley jack. Zero damage as the load is taken the same as the factory scissor jack.

at the front the crossmember as it is one of the stronger points, otherwise use two trolley jacks and under the lower control arms on the front and these are cast and rather strong...

is this the crossmember?? and this diagram is of the r32 gtst, i couldnt find the r33 one.

Yes thats the crossmember....it's in the same place on the R33.

If you want to raise the front of the car you need the jack in the middle of the crossmember at about the centre line of the car. A little trial and error is involved. the car doesn't weigh exactly the same either side of the centreline so it will come up one side lower than the other. Lower the jack and move it an inch or so towards the low side. Repeat the moves until it comes up nice and even.

  • 3 weeks later...

Heres some pics which may help you on where to jack and place stands under the car.

I always jack up on one tow point on the front, then place a stand under the other to get enough height for the jack to get under the cross member. Then simply jack up on crossmember and place stands underneath cross member.

Hope it helps

Frank!

  • 2 months later...

well only if you don't give a **** about the structural integrity of the car.. if I was buying a car its one of the first places i look, to check to see there is no obvious chasis bends. If all the sills etc were bent to shit I sure as hell wouldn't be buying it.

and any workshop that i know was doing that I wouldn't be taking my car to anymore either.

well only if you don't give a **** about the structural integrity of the car.. if I was buying a car its one of the first places i look, to check to see there is no obvious chasis bends. If all the sills etc were bent to shit I sure as hell wouldn't be buying it.

and any workshop that i know was doing that I wouldn't be taking my car to anymore either.

Damn straight!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Actually everyone on the roads was really well behaved. The only person that did any minor tailgating was a local hoon in a Turbo Focus. Unfortunately we weren't going the same way so there was no grand initial D touge battle. Lots of people pulled over and let me through. The amount of "Hey man nice car, omg skyline, nice 34 man woo" was suprising. Like really suprising. Like almost annoying. My partner was obviously surprised, she'd never seen anyone in the real world point out the car/like the car/want to chat about the car before, so to have like 3 people per day mention it was notable, I could finally say SEE? SOMEONE THINKS THEY'RE COOL. Everyone was also pretty suprised about the weather. Every day was dry and about ~13-14C. Mount Wellington had a sign that said they close the gates at 9pm and I was heading up there at about ~7:30. It was VERY apparent that conditions were getting significantly worse by the minute on the way up and down. The road on the mountain was terrible though, it's no driving road. I have various suspension related questions now. Luckily it was only about 20 minutes from where we were staying to the top of the mountain as said Google maps. We only had the 2 nights in Hobart. We went to the Farm Gate Market though which was really good - And went down to the Hastings Thermal springs/caves down there during the day. I'd definitely be up for going back again, so luckily there's a few more sights yet to see. Didn't get to do the west coast/queenstown/cradle mountain so this was supposed to be a 'scouting' trip anyway of sorts if I were to one day do/take part in/organize a more car-focused trip. As for the boat, it wasn't bad. Well it was bad, but not in the way you're thinking. We did the night trip which leaves at 6:45 (though you have to be there ~2 hours earlier) and arrives the next morning at about 6am. There is nothing to do on the ship. If you plan accordingly and bring a book/tablet/show to watch/charger you can just chill out, take some Travacalm and just sleep through it. The food there is an extremely basic buffet that costs $32 a plate, or $14 for a $3 pizza. The way back we had a travel kettle and a few different types of cup noodles and made our own tea/coffee in the room. This was a far superior way to do it. At the very least book one of the rooms with beds. I guess as we were in the off season we didn't have room mates. You get an option for rooms with 4 beds (2x bunks) or a room with just the two bottom beds. There's also some option for a deluxe queen bed but it's much pricer. We've been on sleeper trains in Asia before so we figured this is similar (and it was)
    • You just gotta be really, really, really clear and decisive with what you want your end product to be. 99% of people who want this conversion aren't "I want to run a 295 front tyre!" so they don't really need the widebody. They just want the OEM body to look a little less dumpy, so bonnet, bar, skirts job done with some camber, stretch, slam. It's when you want that, but then decide to pivot later you get big problems. See also if you're willing to get an all in one fibreglass bar, and you're willing to accept fibreglass problems like cracking the entire item on a driveway, instead of just a piece attached to the bottom, etc etc etc. Decide this all before buyin'.
    • After @Kinkstaah debacle, I'd never want to try and get it right 😛
    • The hood lines up with the fenders. The front bar doesn't perfectly line up with the fenders where the wheel arch is. You have to 'squeeze' the front bar 'in' as it wants to naturally flare out and be longer on the sides. There's a few threads where people notice this when they only swap a GTR style bumper and front bar. Unless you have genuine OEM items - you may be better served getting conversion kits. There are GTT bumpers to fit GTR hoods. There are GTR hoods (non genuine) to fit the GTT bracketry. MAY  
×
×
  • Create New...