Jump to content
SAU Community

Recommended Posts

Your not still sooking? :)

As said over on ct.com

It could have still be in cold ign retard and afr enrichment.. It could have been the way it was strapped down.. could have been.... who knows and who cares.. :)

  • Replies 151
  • Created
  • Last Reply

Top Posters In This Topic

Its a few years old. Hitek's as you know is basically bran spankin new.

SR910 was the only person that I know of that had issues on the day so really it was just bad luck.

MS75 with his Toyo 4.5ltr turbo made 391rwkw, Sky30 making 306rwkw on 18-19psi, Terry (x-jms owner) R33 making 350rwkw. So there was plenty of other cars there from other dyno's there on the day that made the power they expected.

I think SR910 just had bad luck on the day.

Nice results Dangerman.

What compression ratio are you running in that engine?

Good luck with the auto. In my experience there is only about 15-20 rwkw difference between auto and manual. That's R34 though but the R33 boxes are basically the same.

Good luck with the auto. In my experience there is only about 15-20 rwkw difference between auto and manual. That's R34 though but the R33 boxes are basically the same.

Good to know, not as much as I expected. The VL auto box's definitely suck a little more out of the motor then.

how much difference does an auto make in regards to spool time? id like to see the results of a manual

it would very much depend on the application, ie rb20/25/30 and the turbo, ie when the turbo is coming on boost. but due to the torque/stall converter in the auto it will give you instantly more revs earlier than a manual hence build boost quicker, not to mention it is easier to load an auto car up on its converter (equivalent to holding the car on the handbrake and slipping the clutch) and get boost happening.. throw a higher stall converter in the autobox and the effect is increased. Whilst your rolling and have some revs/load on board theres prob not as much difference i would say..

  • 2 weeks later...

heres a question for any one who has made the 300kw mark or close to it!

how much ignition timing are you running from 5000rpm and thru to redline?

on the current tune im only running 18 - 19 degrees. thats why i have used so much boost to make the power.

in a week or so i will put it back on the rollers with my new AFM and drop the boost, increase the fuel,

and increase the timing up into the low 20 region.

does anyone else know what timing i should aim for?

18-19degree's really is pretty damn good considering the amount of boost, type of fuel, stock cams, stock inlet and exh. manifold.

So really you are doing well... I'm assuming the motor has been setup to run an 8:1 comp ratio?

Here's a little article on tuning turbocharged vehicles from innovative (the wideband people)

http://www.innovatemotorsports.com/resources/rich.php

What AFM are you looking at?

18-19degree's really is pretty damn good considering the amount of boost, type of fuel, stock cams, stock inlet and exh. manifold.

So really you are doing well... I'm assuming the motor has been setup to run an 8:1 comp ratio?

Here's a little article on tuning turbocharged vehicles from innovative (the wideband people)

http://www.innovatemotorsports.com/resources/rich.php

What AFM are you looking at?

i got a as new q45 from slide..

its only done a couple of thousand kays from new.

a bit weird! it has a 4 pin plug instead of the usual 3!

another member on here has been running up to 24 degrees advance, at less boost to make

more power. thats why i asked

What was there setup with regards to inlet and exhaust manifolds? Cams? It may just be a different dyno reading? Was it an auto?

Exhaust? I forget what yours is.. 3.5" really is a must for over 300rwkw.

A couple of years ago I knew a bloke interstate running around with a GT35r .82 strapped to the side of his RB30DET. He was making ~300rwkw on 18psi. Stock exh. manifold, std plenum, 256duration cams, 5speed. He dropped on a 6boost looking high mount exh. manifold and picked up 30rwkw on the same boost.

What does John think? Its a little low in power compared to what others he has tuned or?

What was there setup with regards to inlet and exhaust manifolds? Cams? It may just be a different dyno reading? Was it an auto?

Exhaust? I forget what yours is.. 3.5" really is a must for over 300rwkw.

A couple of years ago I knew a bloke interstate running around with a GT35r .82 strapped to the side of his RB30DET. He was making ~300rwkw on 18psi. Stock exh. manifold, std plenum, 256duration cams, 5speed. He dropped on a 6boost looking high mount exh. manifold and picked up 30rwkw on the same boost.

What does John think? Its a little low in power compared to what others he has tuned or?

he has a high mount 3540 ex gate

standard motor but with a aftermarket plenum.

and his is a manual. so im not to concerned i was just curious as to how he could run 24 deg when im only on 19?

i guess the plenum would help keep the intake temp down a bit.

and my exhaust is only a 3 inch straight thru.

Johns happy with it in general..

it just comes down to more dollars on the dyno to get it optimal thru out the rev range.

Im curious as to why nismoid hasnt made a comment or shared his wisdom with us!

I think it will have a little to do with the highmount exh. manifold and as a result the ability to run a decent collector with minimal sharp bends.

All aids in maintaining equal reversion across all cylinders. The motors VE would be up as the motor is able to expel the exh. gasses easier not to mention less of the exh. gas will be left lingering in the combustion chamber ready to contaminate and heat the intake charge, which essentially lowers the motors detonation threashold allowing you to run a little more ign timing to get you just that bit closer to MTBT.

As there's less exh. gas in the comb. chamber it also means the motors VE will be up. So more power on the same level of boost or another way to look at it the same power with less boost.

The exh. side of it really is critical as you start getting up over 300rwkw.

But playing with nice exh. manifolds gets expensive and begins to look non stock. UNLESS you can track down a HKS cast item and squeeze that in. They are well designed with no sharp bends with a reasonable collector; well as reasonable as you can get in a low mount.

Shall be interesting to see your results regarding more fuel more ign. timing; blow that article I posted above out of the water. :)

Some very useful points raised here IMO .

Firstly the exhaust manifolds , 300Kw is a long way from Nissans ask with the std iron lump which would have been designed to be compact and durable . The sort of volume and velocity of the exhaust gas flow needed for 300Kw really needs something better and the low cast HKS one is a pretty reasonable compromise of durable/still split pulsed/better flow paths/looks sort of standardish - well more than a fabbed high mount one anyway . I know they do a 3 into 1 on each side but at least the diametre increases as each branch is added .

Exhaust manilold collectors , I keep findind pics of fabbed collectors with this "power pyramid" thing in the middle of where the separate pipes merge . I was always told that making an exhause collector that flowed well in the wrong direction was not a good idea but some of these type manifolds hang off engines making good power .

I still keep scratching my head and thinking could a smaller trim compressor on that GT35R still work response wise as well but with the larger AR 1.06 turbine housing . Any of the 50/52/54/56 trim 82mm GT40 compressors can pump the air required so in theory less turbine load to pump the same volume of air but with less turbine inlet pressure (larger 1.06 housing) should reduce the problems in the chamber ie charge dilution and pre heating . With less of these two factors the ignition timing can probably be pushed a bit more so efficiencies should rise .

I have my own theories on running lower water jacket temperatures and good synthetic oils with lower viscosity and more emphasis on oil cooling to keep the engines head and piston crowns a bit cooler to hold the detonation threshold off a bit longer . I'm not suggesting anyone take this one as gospel so do it at your own risk . I've a bad feeling I'll be going through lots of RB30 blocks trying to get one that will take the piston oil squirters because these and the ceramic coatings may make a noticable difference .

Out of fingers cheers A .

Edited by discopotato03

Hey Disco.

Dangerman4 is running an aftermarket manifold.

http://www.skylinesaustralia.com/forums/in...st&id=55759

http://www.skylinesaustralia.com/forums/in...st&id=55758

All though its probably better than stock the method that has been used to on its collector and and 3 in to 1 method is less than desirable. The HKS low mount definitely has it up on the manifold Dangerman4 is running.

If you want some decent pics of the hks exh. manifold I could grab some for you. Throw the camera in macro mod and take a couple hundred shots getting all and every angle. Thats if you haven't seen in in person. :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...