Jump to content
SAU Community

Horus Finally Got A Gtr :noes:

Horus

By Horus,
in Victoria

 Share

Recommended Posts

Al Grand Master

Al

Posted
Posted
lol_18.jpg

THATS EXACTLY WHAT I WAS THINKING!!

Then i read 490whp on 2510's and did this :)

Jet33 ran 2510's and on full tune/boost with race fuel made about 380rwkw (i think :/ )

Good to see you're still talkin' shit and that daddy FINALLY allowed you to get a GTR :(

PS: American Hp reads high than the rest of the world, something to do with how they calculate it differently, typical Americanisation bullshit. :laugh:

Horus Grand Master

Horus

Posted
  • Author
Posted
THATS EXACTLY WHAT I WAS THINKING!!

Then i read 490whp on 2510's and did this :)

Jet33 ran 2510's and on full tune/boost with race fuel made about 380rwkw (i think :/ )

Good to see you're still talkin' shit and that daddy FINALLY allowed you to get a GTR :(

PS: American Hp reads high than the rest of the world, something to do with how they calculate it differently, typical Americanisation bullshit. :laugh:

har har

Im in canada foo

and no...it wasnt run on a mustang dyno Lo!!!!!

and for the record I work 2 jobs and the car cost me 30k canadian....600 per month...if dad was buying me a car Id drive an S500 like him!!!!!

hey are you still ugly as dogs balls?

Al Grand Master

Al

Posted
Posted

:( Same petty little boy. Have you made new friends with the primary kiddies yet? You'll fit right in :laugh:

Unlike yourself, i don't "bat for the same team", and you're not my type anyway :/

PS: I didn't say "buy" i said "allowed" :)

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      NC MX5

      By Dose Pipe Sutututu · Posted

      Lamb roast on Saturday will be different 🥲
    • TurboTapin
      RB25DET with solid lifters - which cams ?

      By TurboTapin · Posted

      They are under bucket shims. Tomei provides a test shim kit and then any measurement of shim required. 
    • GTSBoy
      RB25DET with solid lifters - which cams ?

      By GTSBoy · Posted

      I always wondered how you were supposed to buy a set of 24 buckets and somehow magically have every single one of them yield exactly the desired clearance. I would have thought you'd need to assemble a cam with either 12 "sample" or "example" buckets of known top thickness (or a single such sample/example 12 times over!!) measure clearances at every valve, and then do the usual math to work out what the actual "shimness" of each bucket needed to be, before buying the required buckets to make up he thicknesses that you didn't have on hand.
    • TurboTapin
      RB25DET with solid lifters - which cams ?

      By TurboTapin · Posted

      I now seem to be limited in power due to my rev limit/hydraulic lifters in my built RB25. I'm looking into converting over to Tomei solid lifters. Question for anyone that has done the conversion. I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  I don't know where I got this idea, as so far I see no mention of this in any of the Tomei documentation. It just states I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
    • TurboTapin
      Why am I hitting a power wall with my stroked RB25?

      By TurboTapin · Posted

      I couldn't agree more. I should have started from the get-go with a NEO or solid bucket conversion. I started looking into converting over to solid lifters yesterday. Now for some reason I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  But I see no mention of this on any of the Tomei documentation. It just states that I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
×
×
  • Create New...