Jump to content
SAU Community

Recommended Posts

Ok so

so far the car has got all the supporting mods

Walbro Gss432 pump

adjustable fuel pressure regulator

full 3" exhaust with dump pipe

HKS pod and intake

boost regulator

SAFC II

FMIC

New 02 sensor

New ECU temp sensor

I am running 7psi at the moment, and when i got o tune the SAFC II i want to run 12psi and no more, less if i can get away with it.

The tunner told me that 160rwKw is basically what is actually posible, i have no idea why, that is only a 40kw increase over stock.

Now basicaly intake and exhaust is a good 10kW, pod 5kW, 5psi boost 40kW, remap, about 10kW so that should be a total gain of about 65kw. Now stock at the RW is about 120-130kW so that should be about 180-190rwKw in total

So what the helll is he on about.

Can people post up their output figures with the mods. I am not too sure if the tuner can be trusted but that is the only one poeple have recomended.

What sourght of power figures should i be looking at, and what do i tell the tuner to do, ie fuel air rations and recomendations to my tune.

HELP PLEASE, i want to get this right, as i am on a budget. Thanks.

SILLY ME. she's a 1995 R33 series 1.5. Opppsa

Edited by WogsRus
Link to comment
https://www.sau.com.au/forums/topic/134905-car-booked-in-for-a-tune-safc-ii/
Share on other sites

1.What car is this for btw? R32 Or R33 Or R34?

2. How much power is the car making now prior to installing SAFC + tuning?

3. What turbo are you running? stock?

4. If its a r33 with the mods you have listed on stock turbo i personally believe you'll be getting between 170-190rwkw as well. If its an r32 then 160rwkw is my guess.

my 2cents

remember auto's dont read aswell on dyno's as manuals do,

i was told by my tuner,he said it reads a little higher down low

(something to do with the torque) and read low up top.

89' rb20det r33 turbo+zorst & SAFC1 automatic = 165rwkw

12psi

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Man, different parts but the same numbers is terrible @dbm7! And it doesn't help that most online shops don't list the part numbers at all. They just give a list of compatible models...
    • Slow when hot could also be because its getting more dynamic compression, OR things are getting a bit tighter once it is all expanded. If it were an earthing issue, typically I'd expect you to have it have issues all the time. Unless it's really a combination of both things. Where the higher compression, and things being a bit tighter, is giving that bit of extra load and you do need a slight clean up on the cables/connections.
    • Yeah, this is one of the most annoying things about nissan part numbers... I've got an unrelated example... Image is of the AT output shaft ~ they have the same part#, but clearly the shaft on the left is beefier design to that on the right ...the difference (essentially) is the 'lighter' shaft on the right, is for engines up to RB25DE (this includes RB20 variants) : the shaft on the left is for RB25/26DET(T)....are they interchangeable? Yes...but obviously one shaft is going to be stronger than the other...and, the lighter shaft is around USD115, but the heavier shaft closer to USD150...same part#... ...epc-data usually tells a tale ~ the amayama listing for 39100-23U60 has a note "Longest side is between 60 and 105 cm" ; no such info is there for 39100-23U70 ...and given the great disparity in price between the 2 parts, it makes me at least curious (to the point of caution) where the 'extra money' went? ...ie; these 2 parts have a cost difference that (to myself at least) isn't explained by 'plastic boot'...ie; with amayama there's AUD700 price difference ...plastic versus rubber?...I'm not seeing it like that...and 60cm ~ 105cm...??...that's a huge disparity....something hinky going on here... I'd try searching by VIN, not model... /2cents
    • I don't know for sure, but I'd expect them all to be interchangeable given the diff end and hub end don't move/change between any C34 series. Often Nissan will change part numbers and the aftermarket follows those year ranges; but the original part number change doesn't mean other parts won't fit. The change could be a change in material, internal parts or even just supplier. For example, all the RB gearbox to engine bolts are no longer available and there is a new part number instead. The only change is they went from cadmium plated bolts to zinc plated due to the issues manufacturing with Cadmium. They look different but work the same.
×
×
  • Create New...