Jump to content
SAU Community

Recommended Posts

first of all. what is your budget and application.

then work from there.

your options are:

- drop in a motor from a turbo model

- turbo your current motor

as to the differences between a gtr and gtst:

the answer is heaps....

2.6L twin turbo with attessa vs. 2.5L turbo rwd

different brakes, interior, body shape

list goes on...

do a little research, and search through the forums and internet... try the search button up top on this forum.

It's not worth it to turbo your na unless you really want to. There have been many threads on this. you'd be better off dropping in a turbo motor.

Also, aftermarket turbo on an na motor is also probably even worse. the na motor is probably only good for 7-8psi (stock turbo) since it's a high comopression motor. There's no point gettign a big turbo if you will only end up running 1 psi to have it flow the same as the stock turbo at 8psi (it won't even run at 1psi anyways).

It's not worth it to turbo your na unless you really want to. There have been many threads on this. you'd be better off dropping in a turbo motor.

Also, aftermarket turbo on an na motor is also probably even worse. the na motor is probably only good for 7-8psi (stock turbo) since it's a high comopression motor. There's no point gettign a big turbo if you will only end up running 1 psi to have it flow the same as the stock turbo at 8psi (it won't even run at 1psi anyways).

A bigger turbo spools at more user-friendly revs, a guy I knew had a TO4E on his high-comp R34 and it spooled like the stock turbo. Stock turbo's on high-comp engines tend to be pushing 7psi at 1800rpm, it's awesome around town though, tons of torque low-down.

Cant you just lower the compression ratio of the engine?

My parents mechanic told me that i could throw a hks stage 1 turbo kit straight on and you just have to adjust the engine to be able to run it.

Cause im after an r33 gts25 as well for my first car, And im concidering doing this once im off my p's

Edited by OBNXSH
Cant you just lower the compression ratio of the engine?

My parents mechanic told me that i could throw a hks stage 1 turbo kit straight on and you just have to adjust the engine to be able to run it.

Cause im after an r33 gts25 as well for my first car, And im concidering doing this once im off my p's

its not something you can adjust like timing, you'll have to throw in a thicker head gasket or swap pistons.

and even then you will still only be able to run mild boost without doing more work.

that said how old are you? QLD govt. is implementing the P plater restrictions soon (as you probably already know) and by the time you get onto your P's you may not want a skyline anymore. at the current price of skylines its much easier (and costs roughly around the same) to sell and buy a GTST

its not something you can adjust like timing, you'll have to throw in a thicker head gasket or swap pistons.

and even then you will still only be able to run mild boost without doing more work.

that said how old are you? QLD govt. is implementing the P plater restrictions soon (as you probably already know) and by the time you get onto your P's you may not want a skyline anymore. at the current price of skylines its much easier (and costs roughly around the same) to sell and buy a GTST

I know all about the p plater restrictions i have the pain in the ass memorised. I get my P's in less then a year. Ive been set on a late 90's model c200 mercedes or an r33 as long as i can remember, And the mercedes is a little out of my price range so i wanna settle with an N/A skyline and in the future work on it, Money really isnt an object for me so if that is the main reason why people say to not convert the engine, Is there any other reasons as to not do it disregarding money? Plus n/a skylines ive looked at have been roughly 8 - 10k and importers have quoted me roughly the same price...

Edited by OBNXSH
Money really isnt an object for me

if only we were all so lucky....

reasons to do the conversion it:

- you might already have a bodykit on your skyline

- stereo install

- small dress up bits, custom bits,

- rims

- suspension work

reasons not to do it:

- brakes will need upgrading

- a standard RB25DET is made to take the power

- a DET motor you can be looking at 200rwkw or more on standards

- much less customization

- gearbox

its all common sense really... if you do a search you can find your answers

talk's cheap. for someone who cant even drive yet you are certainly thinking very far ahead... i suggest you get your license and then go from there.

by the time you get your p's turbo 33's will probably be cheap enough for you to buy 1, but you won't legally be able to drive it.

if you want a NA skyline as your first car then get that. then once you are off your p's either sell it and buy a turbo skyline, or drop the motor out and put a turbo motor in. here are some of the mods you have to do-

buy the turbo, intercooler and piping, and manifolds and exhaust

buy a new clutch

get a thicker headgasket put on

get a new ecu (to have it run well)

new fuel pump

have oil and water lines drilled into the head

now if you go an aftermarket turbo setup, you are looking at $2500-$3000 just for the turbo, which is the same money as a turbo front cut. but the turbo motor will handle much higher amounts of boost. an the boost you could run on the NA motor with a turbo, you probably would only just make it to the power of a stock turbo motor, if you were lucky.

Just get a shit car for your first car, save up and get something nice once youve crashed it and are off your Ps.

You will scratch it up, you dont want a nice car for your first car and you sure as hell don't want a fast car.

if money isnt a problem how can the c200 be out of your price range?

The type of c200's i want, In the condition i want are 22 - 26k.

Just get a shit car for your first car, save up and get something nice once youve crashed it and are off your Ps.

You will scratch it up, you dont want a nice car for your first car and you sure as hell don't want a fast car.

Bit to late bought a 33 yesterday...

Im not to fussed about a turbo or not i was just saying thats was what the mechanic dude said.. Ill probly buy a merc once im off my p's. Lol i dont really care about how fast it goes :D

Edited by OBNXSH

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • And if you want more power, more reliably, and cheaper, go get the Aussie RB... The 4L Barra and put that in instead.
    • No cats will keep discolouring the rear bar. Sends white paint a weird yellow stain. Cut and polish normally gets it out, but you'll be doing that every fortnight I found.
    • Both heads will be equally reliable or unreliable depending on what you do to them.  Stock the RB26 head will flow more. You have access to the stock intake ITB manifold on the RB26 cheaply which flows really well(1000hp+).   Arguably more aftermarket support for RB26, though in Aus we love our RB30 SOHC heads too.    The only downsides to the RB26 head is if you have a VL commodore and want to keep the SOHC look.  Where you may have an issue is drilling out the rb30 block for the bigger head studs but if you are building a big power motor you'd probably put bigger studs on the SOHC head too.  This is just about finding a good machine shop, sometimes easier said than done.  RB30 head worked can make big power just like a Rb26 head, so really it actually more comes down to what your preference is for your car.  People now even making billet versions of both.
    • 2630s work perfectly well. There is something to be said for just using the 30 head, as it saves all the pain of the conversion, still makes tons of power, still sounds cool, etc etc. 2630 will obviously make more power again, but the differences are not stupidly big. It really depends on whether you're racing for sheep stations or not. If it's dead serious, then it's a 26 head. If it's just for fun, it could go either way. But the 26 head and the effort to get it set up, etc etc, is part of the fun.
    • I've been building a 26/30 for a few years now. I've had the head built with all the good stuff. I had a 32 gtr but blew it up and yes its all going into a vl but im looking for some advice from some RB nuts on pros and cons on putting a 26 head on a 30 bottom end is it worth it Works are as follows Head -Extensive porting 1mm oversized supertech valves Supertech double springs Supertech valve guides Supertech titanium retainers Tomei solid lifters Tomei 270 x 10.25 cams Head drain Bottom end series 2 rb30 block Cp ceramic coated pistons Eagle rods Romac balancer Oil restrictions  O ringed blah blah spent a fortune And will get a girdle because the 30s arent used to handling that much rpm Nitto billet oil pump Hypertune plenum 6boost mani Refurbed astra pump thats the cover for it in the boot I did have a precision 6262 but sold it because drag car life. Currently building the ass end full 4 link floater rear end with a 2 speed  But the dilemma i have is my mate rekens I should just stick with the 30 head for reliability. Has any one had any issues with mounting the 26 head ie compression blowing gaskets etc. Just looking for some advice from people who have gone down this route. Here's some photos. Blew the oil pump in the gtr and decided to rip the motor out at the time and do a full build only to find it had been a repairable write off so went down this path.     
×
×
  • Create New...