Jump to content
SAU Community

Recommended Posts

This was my 2nd time at the drag strip.

i am happy to get into the 14's as my other best was 15.06

What do you think of my Drag slip

Reaction Time 0.117

60' Time 2.31

1/8 Time 9.67

1/8 kmh 124.49

1/4 mile Time 14.78

Trap Speed 156.31

any comments tips trick would be great

  • Replies 52
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

yea 201.3rwkw with a Manual trans.

the Drag racing thing is not as easy as it looks haha

i was launching at 3500rpm and dumping the clutch and then changing to 2nd as quick as possible to stop wheel spin.

Edited by r33madd

Disregarding the time, the trap speed of 97mph (converted) means you don't have anything close to 200rwkw. With that kind of power you should be expecting at least 105mph, and probably closer to 110mph.

Then again your run wasn't done on a Dyno Dynamics but still, that dyno that was used seems pretty optimistic.

That 60 footer is pretty horrible.

Backing of a little instead of changing to second might be better. This is what i do, the RB just feels so much happier in the high revs.

With a pod, boost controller and cat back exhaust,

I managed a 13.6 with a 60 footer of 2.0....

14.78 is half a second slower then the official time for an r33 gts-t isnt it?!?!

Go back again with better tyres.

What tyre pressure do most of you use.

What Revs is a good level to launch at.

Whens the best time to change gears

What 60ft time would i need to get a low 14 or a high 13

and when you say backing off a bit wouldnt that hert my time even more.

from the look of your sig the rear of your car is too low... very hard with the IRS to get traction when it's that low, no room for squat or weight transfer

also are you running any kind of fuel controller? if you are running those mods off the stock ecu it will be way too rich, esp. with an aftermarket pump in there

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hey keep the ideas coming, I'm always keen on projects! But, problem fixed!  I got a cheapie ozito scope from Bunnings and had a good look in and around the bearing and sensor hole. I couldn't see a smoking gun but the bearing looked a bit strange, especially when comparing with a new one. I thought the cover had come off the bearing magnets.  Sorry for pics of a screen, I didn't have an SD card.     Good thing I had the old one to inspect. So, given I'm like a pit crew with wheel bearings and luckily I had a spare bearing because I f**ked up my parts order, I decided to just smash it out. Got the old one out in about an hour. So much easier when the parts haven't had a chance to rust together yet. 😂 And, well, found the problem.    In the second pic at about the 8 o'clock position, you'll see what I think is the tip of the old sensor.  The new sensor has definitely been rubbing but it's all intact, just a little shiny so I'm hoping it's fine.  The car brakes perfectly now and no errors.  I think the job took about 2.5h in the end. 👍🏻 I really appreciate the help in here as usual. Thanks guys.
    • I was only looking because I saw some drops on the ground but it wasn't alot. Recently had it serviced will ask the mech to confirm. Find it strange that it looks standard though, can see in another photo of a random box 
    • So...not sure if you know if that has always been there or why you went looking. It could be old damage from a clutch explosion, or even just the gearbox got dropped somewhere along the line. Basically, you should seal it up to stop oil and dust getting into the bellhousing, but it doesn't matter too much and is not structural. I'd suggest something like a glob of JB Weld. BTW what gearbox oil are you running, I would guess the breather has been spewing it everywhere.
    • Hey Duncan thanks for your reply. Sorry mate I know the photos are shit.  Took another photo for reference. Seems the casing does have a hole in it looking on the net, fluid seeping out. Added a photo   
    • Very hard to make out what you mean, is it the squarish hole with redline shockproof (probably) under it? Is that pic from on top of the engine with the firewall to the left of pic and engine to the right? Either way, spray the area liberally with degreaser and try again, maybe circle the part you are worried about
×
×
  • Create New...