Jump to content
SAU Community

Recommended Posts

As topic states, I am putting my car up for sale but first just wondering what you guys think would be a fair price to ask... I know alot of the money you spend on mods don't really count for much when you go to sell it but here it all is anyway (i would have posted in the sale section but it's not for sale yet!)

96 GTS-T 90,000ks

Full veilside kit

17" rims

T3/4 turbo producing 300+rwhp @1bar

Apexi AVC-R

Apexi Power FC and hand unit

3" exhaust from the turbo back

9 Puck extreme ceramic clutch with 2500 pound pressure plate (in the process of being fixed as its making kinky noises)

HKS intercooler

HKS filter

GFB fart valve

GTR fuel pump

1k alarm (discount insurance)

4k stereo with 2 12" subs with custom install in boot

um prolly missing out some other bits.... apart from the dogey clutch and a couple of very small chips on the front bar its running sweet as

any ideas? cheers miles

Link to comment
https://www.sau.com.au/forums/topic/13613-rice-has-to-go-what-it-worth/
Share on other sites

yeah dood seriously the series II aspect will net you a few more dollars anyways, cos of the air bags and definate ABS well mostly. Especially to people starting to get into skylines. for others who have purchased cheaper skylines a series II doesnt represent too much extra value, but you will find more people will like the more updated look.

the mods will definately get more dollars, i reckon honestly you could remove most of the mods and still sell the car for $26

especially if it all neat/clean and immaculate basically.

The mods will net you more money on their own

Just look at car yards, and you got decent km's as well

anyways good luck with the sale when you do sell it mate

get pauls wing, that will get ya an extra thousand

Paul....peace brother you know I am playing, i love it man

little high but smeh its the goods

selling for a few reasons partly on the 10 minute drive to work this morning a saw about 11 skylines.... yeh i know market is tough, but I'm not out to rip anyone off infact i think i will give a really good deal. But your right it might end up going for a lot less with less modz...

you know how it all started?

in the USA they had huge roadside bill boards with GOT MILK? to remind people to grab some on way home. turbo and high tech mag picked up on it after that. i bought one of their shirts in the states bout 5 years ago. my wife bought my plates for my RX3 i had at the time.

I honestly think coming from a sales point of view that you should sell and swap parts... this way would get you money and you could probably sell what left for about 22. ie sell and trade the turbo AVCR fuel pump all the extras for an amount.. you will prob make an extra 2G or so this way....

You already have a buyer if you want to sell some of your stuff... ME! so it is a win win situation! i can trade you stuff plus $$$

up to you though.. otherwise go for about $25 - 26 maybe more!.... your car is still in good nic :-)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...