Jump to content
SAU Community

Recommended Posts

Just because a car has been track driven, dosen't mean it hasn't been looked after.

Just check for the normal issues that you should be checking for anyway.

- Compression / Leak down test.

- Checkout any unusual suspension / steering noises.

- Ensure that gearbox feels nice.

- Brakes usually get a hard workout, so ensure that rotors are in good shape.

I might have missed something, but that's all I can think of for now.

Link to comment
https://www.sau.com.au/forums/topic/137697-track-days/#findComment-2563992
Share on other sites

hi guys

what are the things to look out for?

if purchasing a car and if its done any or allot of track days?

if so what wear and tear is and is not serios to the cars health?

post your thoughts guys

thanks

I see no issues in buying a car that has done club sprints before, as generally any wear and tear is made up for by how well the owner usually looks after the car. They are generally over serviced, and fixed regardless of cost. People generally don't use cheap crap when going to the track.

That's my opinion anyway, some may disagree, but I do sprint days and I know how well I, and the other people I know who do them, look after our cars.

Link to comment
https://www.sau.com.au/forums/topic/137697-track-days/#findComment-2569705
Share on other sites

I agree 100% with the above. From what I have seen a car used for the occassional track day gets very well looked after. Personally there is no way I head out to track days unless the car is tip top, ie all the brakes/suspension/drivetrain/engine is good. I have seen people try with cars that are less than well prepared & inevitably they go home early with a busted car.

They wear items are pretty obvious:

Brakes.

Suspension bushes.

Engine.

In other words things that can easily be checked.

Link to comment
https://www.sau.com.au/forums/topic/137697-track-days/#findComment-2569919
Share on other sites

I'll guarantee you that any skyline you look at will have been driven hard at some time. It's what they do.

If it's done track days, it'll have been re-oiled and checked over before and after, unless the owner is simply crazy. If it has never done track days, it might have been driven hard and looked after, or it might not have.

Just keep your wits about you and get a feel for the seller. If you think he's nuts, then walk away.

Link to comment
https://www.sau.com.au/forums/topic/137697-track-days/#findComment-2570236
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...