Jump to content
SAU Community

Quick Bov Question

koo

By koo,
in Engines & Forced Induction

 Share

Recommended Posts

r32matt Collaborator

r32matt

Posted
Posted

If your talking about Turbo Flutter you can get that sound by just removing your BOV. Aftermarket BOV's do this as well becasue the spring is stronger than a stock BOV, so it only opens up at high boost. Stock BOV's have a soft spring so they open on low boost. When the BOV doesnt open the air bounces off the turbo inside the pipes casuing it to make the Flutter sound. So the when your not running high boost the BOV wont open and you will get the Flutter sound or as you say psstt...ttts...ttts...ttts...ttts..ttts, lol.

:/

Modena Grand Master

Modena

Posted
Posted
If your talking about Turbo Flutter you can get that sound by just removing your BOV. Aftermarket BOV's do this as well becasue the spring is stronger than a stock BOV, so it only opens up at high boost. Stock BOV's have a soft spring so they open on low boost. When the BOV doesnt open the air bounces off the turbo inside the pipes casuing it to make the Flutter sound. So the when your not running high boost the BOV wont open and you will get the Flutter sound or as you say psstt...ttts...ttts...ttts...ttts..ttts, lol.

:/

which offcourse f**ks the turbo up :)

Rolls Grand Master

Rolls

Posted
Posted

Its actually running no bov at all that makes that sound, if you block up your stock one the air will have no where to go when the throttle closes so it reverses and goes back through the compressor blades getting chopped up and then back out the pod. This gives you the flutter noise.

A big thread on it here http://www.skylinesaustralia.com/forums/in...showtopic=60655

locoloc Community Regular

locoloc

Posted
Posted

Does anyone know if it would make any difference (to performance or sound) if i was to put my hksssq where my stock one is. when i brought the car it was configured in a wierd way where a hks bov was installed but the tubes connected up to the stock bov and in affect im running 2 bov's.

I just wanted to clean up and possibly gett the fluterr sound so was wondering if i directly replaced the stcok one for the hks one would it affect performance and can i get the flutter.

cheers.

R33S2 Grand Master

R33S2

Posted
Posted

locoloc: are you sure the standard one isnt blocked off with a gasket between the flange? But yes you can run just the one if it will fit on the flange.

DFAULT: on most there is a bolt with a lock nut, adjusting this will make it softer or harder.

Rolls Grand Master

Rolls

Posted
Posted
Does anyone know if it would make any difference (to performance or sound) if i was to put my hksssq where my stock one is. when i brought the car it was configured in a wierd way where a hks bov was installed but the tubes connected up to the stock bov and in affect im running 2 bov's.

I just wanted to clean up and possibly gett the fluterr sound so was wondering if i directly replaced the stcok one for the hks one would it affect performance and can i get the flutter.

cheers.

If you want the flutter sound you have to remove/block off both your bov's.

Is the HKS one set up so its recirculating?

thrtytwo Veteran

thrtytwo

Posted
Posted
If you want the flutter sound you have to remove/block off both your bov's.

Is the HKS one set up so its recirculating?

im pretty sure that somehow the HKS SSQ somehow opens - closes - opens - closes, gving not quite a flutter sound, but a sequential release, dont quote me though :wave:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Mistakes were made, my R34 Story

      By MBS206 · Posted

      The oil pressure sensor for logging, does it happen to be the one that was slowly breaking out of the oil block? If it is,I would be ignoring your logs. You had a leak at the sensor which would mean it can't read accurately. It's a small hole at the sensor, and you had a small hole just before it, meaning you could have lost significant pressure reading.   As for brakes, if it's just fluid getting old, you won't necessarily end up with air sitting in the line. Bleed a shit tonne of fluid through so you effectively replace it and go again. Oh and, pay close attention to the pressure gauge while on track!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I don't know it is due to that. It could just be due to load on track being more than a dyno. But it would be nice to rule it out. We're talking a fraction of a second of pulling ~1 degree of timing. So it's not a lot, but I'd rather it be 0... Thicker oil isn't really a "bandaid" if it's oil that is going to run at 125C, is it? It will be thicker at 100 and thus at 125, where the 40 weight may not be as thick as one may like for that use. I already have a big pump that has been ported. They (They in this instance being the guy that built my heads) port them so they flow more at lower RPM but have a bypass spring that I believe is ~70psi. I have seen 70psi of oil pressure up top in the past, before I knew I had this leak. I have a 25 row oil cooler that takes up all the space in the driver side guard. It is interesting that GM themselves recommend 0-30 oil for their Vette applications. Unless you take it to the track where the official word is to put 20-50w oil in there, then take that back out after your track day is done and return to 0-30.
    • PranK
      My new to me M35 Stagea wagon

      By PranK · Posted

      Nice, looks great. Nice work getting the factory parts also. Never know when you'll need them.
    • Chupapy
      New r33 owner

      By Chupapy · Posted

      Thanks @jtha7 I will have a look around tomorrow but it is a prick of a spot. These are some photos i tried taking 
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I take it that the knock retard is from bearings tapping a little tune? Thicker oil is a fragile bandaid. You need a much bigger oil cooler and probably the bigger pump being discussed.
×
×
  • Create New...