Jump to content
SAU Community

Dry Sump Setup Pics

widebody32

By widebody32,
in Engines & Forced Induction

 Share

Recommended Posts

Beer Baron Grand Master

Beer Baron

Posted
Posted
wouldnt happen to have a spare inlet manifold from the gt500 engine?

what will you do for me dave if I quickly steal that inlet next time i'm near one? I don't think nismo will give me one for love or money. and i've given them both over the years and they've given me some nice shit, but GT engine might push it! hope you get some inspiration from the pics though. :P

  • 1 year later...
BoostdR Mentor

BoostdR

Posted
Posted

here you go you picture hungry animals. threw in a few nismo engine pics to make up for the slowness.

NISMO JGTC RB26 DRY SUMP SET-UP:

picture789hx1.jpg

picture792gy8.jpg

picture786gt8.jpg

picture791vj9.jpg

picture788qt7.jpg

picture790ir1.jpg

now that i see it's on a little dolly i should have wheeled it home :w00t:

I see they aren't to stressed about harmonics....full counter weight no doubt

Beer Baron Grand Master

Beer Baron

Posted
Posted

yeah no real balancer as such, just a crank pulley to drive the water pump, alt and oil pump... everything would be finely balanced from end of crank to the clutch, not sure if the crank is full counter weight but it probably is.

bigmikespec Veteran

bigmikespec

Posted
Posted

Couple of things:

Have people who have done a full dry sump setup with a RB26 retaining the 4WD bothered take advantage of a shallower oil pan and lowered the engine? I can imagine it being a bit of a task especially to maintain the suspension and driveshaft geometry.

Is it necessary to run an oil restrictor to the head?

Hoping Brad (Risking) will comment on the first question.

bigmikespec Veteran

bigmikespec

Posted
Posted

You can't lower the engine much as the pan is not shallower where it goes over the A frame cross member and power steering. The sump box hangs in the abyss....

Matt

Good point; need to go under and measure.

Beer Baron Grand Master

Beer Baron

Posted
Posted

yeah given driveshafts still going through the sump/diff in the front it's not easy to drop the engine much if at all. plus if the car is already really low (using just adjustable shocks) then driveshaft angles are already fairly bad.

if you went to a remove front diff (like a hilux etc) arrangement then you'd be in business. but such a hassle.

Risking Grand Master

Risking

Posted
Posted

It's not hard to do at all.

I make the shafts with uni joints instead of constant velocities and put a good splined slip joint at one end to allow for length changes.

Never had a binding issue with lowered engines.

It also helps if you run a higher offset rim and move the hub outward utilizing longer front drive shafts. I think I know what mike has in mind hence the above suggestion he will understand.

The sump bulge gets cut off and critical parts of the diff casing need to be webbed into the pan.

Something I've also been stuffing with is a brace incorporated into the outter diff/sump flange which braces the diff casting to the block. It has seemed to help with the whole snapping diffs of with launching issue I used to have.

bigmikespec Veteran

bigmikespec

Posted
Posted (edited)

It's not hard to do at all.

I make the shafts with uni joints instead of constant velocities and put a good splined slip joint at one end to allow for length changes.

Never had a binding issue with lowered engines.

It also helps if you run a higher offset rim and move the hub outward utilizing longer front drive shafts. I think I know what mike has in mind hence the above suggestion he will understand.

The sump bulge gets cut off and critical parts of the diff casing need to be webbed into the pan.

Something I've also been stuffing with is a brace incorporated into the outter diff/sump flange which braces the diff casting to the block. It has seemed to help with the whole snapping diffs of with launching issue I used to have.

If you lower the engine you decrease your driveshaft angle which increases you track... so the proper way to do it would be to do what you suggested, you would not need longer driveshafts but the decreased angle might be an issue?

Why the move to uni's Brad? Sounds like a good idea RE: front diff casing.

Mr Baron: it is funny you mention removing the front diff. some mad fabricator in Sydney outlined plans for such a conversion :rolleyes:

Edited by bigmikespec
bigmikespec Veteran

bigmikespec

Posted
Posted

Not measuring the angle of the driveshaft it is hard to tell how much but it will vary. Want to get under and have a look this weekend. Also to check what Matt mentioned.

You are quite the argumentative type :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      boost source Size Garrett gt28 gen2

      By TurboTapin · Posted

      You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • QB6SAGR
      Battle of the broken skylines

      By QB6SAGR · Posted

      Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • cosline
      R32 gtr transmission strength, billet plate

      By cosline · Posted

      Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Rezz
      Spotted on the street....

      By Rezz · Posted

      Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...