Jump to content
SAU Community

Dry Sump Setup Pics

widebody32

By widebody32,
in Engines & Forced Induction

 Share

Recommended Posts

Beer Baron Grand Master

Beer Baron

Posted
Posted
wouldnt happen to have a spare inlet manifold from the gt500 engine?

what will you do for me dave if I quickly steal that inlet next time i'm near one? I don't think nismo will give me one for love or money. and i've given them both over the years and they've given me some nice shit, but GT engine might push it! hope you get some inspiration from the pics though. :P

  • 1 year later...
BoostdR Mentor

BoostdR

Posted
Posted

here you go you picture hungry animals. threw in a few nismo engine pics to make up for the slowness.

NISMO JGTC RB26 DRY SUMP SET-UP:

picture789hx1.jpg

picture792gy8.jpg

picture786gt8.jpg

picture791vj9.jpg

picture788qt7.jpg

picture790ir1.jpg

now that i see it's on a little dolly i should have wheeled it home :w00t:

I see they aren't to stressed about harmonics....full counter weight no doubt

Beer Baron Grand Master

Beer Baron

Posted
Posted

yeah no real balancer as such, just a crank pulley to drive the water pump, alt and oil pump... everything would be finely balanced from end of crank to the clutch, not sure if the crank is full counter weight but it probably is.

bigmikespec Veteran

bigmikespec

Posted
Posted

Couple of things:

Have people who have done a full dry sump setup with a RB26 retaining the 4WD bothered take advantage of a shallower oil pan and lowered the engine? I can imagine it being a bit of a task especially to maintain the suspension and driveshaft geometry.

Is it necessary to run an oil restrictor to the head?

Hoping Brad (Risking) will comment on the first question.

bigmikespec Veteran

bigmikespec

Posted
Posted

You can't lower the engine much as the pan is not shallower where it goes over the A frame cross member and power steering. The sump box hangs in the abyss....

Matt

Good point; need to go under and measure.

Beer Baron Grand Master

Beer Baron

Posted
Posted

yeah given driveshafts still going through the sump/diff in the front it's not easy to drop the engine much if at all. plus if the car is already really low (using just adjustable shocks) then driveshaft angles are already fairly bad.

if you went to a remove front diff (like a hilux etc) arrangement then you'd be in business. but such a hassle.

Risking Grand Master

Risking

Posted
Posted

It's not hard to do at all.

I make the shafts with uni joints instead of constant velocities and put a good splined slip joint at one end to allow for length changes.

Never had a binding issue with lowered engines.

It also helps if you run a higher offset rim and move the hub outward utilizing longer front drive shafts. I think I know what mike has in mind hence the above suggestion he will understand.

The sump bulge gets cut off and critical parts of the diff casing need to be webbed into the pan.

Something I've also been stuffing with is a brace incorporated into the outter diff/sump flange which braces the diff casting to the block. It has seemed to help with the whole snapping diffs of with launching issue I used to have.

bigmikespec Veteran

bigmikespec

Posted
Posted (edited)

It's not hard to do at all.

I make the shafts with uni joints instead of constant velocities and put a good splined slip joint at one end to allow for length changes.

Never had a binding issue with lowered engines.

It also helps if you run a higher offset rim and move the hub outward utilizing longer front drive shafts. I think I know what mike has in mind hence the above suggestion he will understand.

The sump bulge gets cut off and critical parts of the diff casing need to be webbed into the pan.

Something I've also been stuffing with is a brace incorporated into the outter diff/sump flange which braces the diff casting to the block. It has seemed to help with the whole snapping diffs of with launching issue I used to have.

If you lower the engine you decrease your driveshaft angle which increases you track... so the proper way to do it would be to do what you suggested, you would not need longer driveshafts but the decreased angle might be an issue?

Why the move to uni's Brad? Sounds like a good idea RE: front diff casing.

Mr Baron: it is funny you mention removing the front diff. some mad fabricator in Sydney outlined plans for such a conversion :rolleyes:

Edited by bigmikespec
bigmikespec Veteran

bigmikespec

Posted
Posted

Not measuring the angle of the driveshaft it is hard to tell how much but it will vary. Want to get under and have a look this weekend. Also to check what Matt mentioned.

You are quite the argumentative type :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      New kid on the block

      By GTSBoy · Posted

      The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Duncan
      New kid on the block

      By Duncan · Posted

      Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • iain_ST44GA
      M35 VQ25DET starter motor

      By iain_ST44GA · Posted

      Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
    • Murray_Calavera
      R33 GTR running -9 with no tune

      By Murray_Calavera · Posted

      I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
×
×
  • Create New...