Jump to content
SAU Community

Recommended Posts

Not sure if this is the right place to put this but..

Ive read somewhere that petrol loses its OCTANE level after a period of time.

So approx how long does this occur? Is this true?

For example I fill up the car with BP Ultimate 98RON, how long will it take to "expire" and lose its "98RON" properties?

Is it bad for the car if there is fuel in the tank from like say 6 months ago?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/138836-petrol-expire/
Share on other sites

I'd leave fuel in the tank, an empty tank tends to rust.

And some light reading on the subject:

http://www.chevron.com/products/prodserv/f...detecting.shtml

http://www.virginiawind.com/tips/gasoline_stabilizer.asp

http://www.challengers101.com/FuelStorage.html

The last one is the most generally informative. I was looking for a deterioration duration curve [time vs decay] but couldn't find one.

Link to comment
https://www.sau.com.au/forums/topic/138836-petrol-expire/#findComment-2585746
Share on other sites

less wh0ring more explaining.

maybe around two weeks it would drop a bit of its just sitting there in the tank?

Hmm interesting.. thanks Paul! :)

Mate works at an Audi workshop, they had a car sitting for 2 years and someone tried to start it. The petrol had thickened and needed new lines and pump as they were all clogged up.

lawl two years

Link to comment
https://www.sau.com.au/forums/topic/138836-petrol-expire/#findComment-2586284
Share on other sites

a friend who used to run a local servo a few years back said it drops octane even while sitting in the tanks at the servo. so servos that dont do as many customers, fill up less often, are likely to have lower octane fuel than a busy store than fills up reguarly

Link to comment
https://www.sau.com.au/forums/topic/138836-petrol-expire/#findComment-2586327
Share on other sites

Official word from Shell is that their fuel will be stable if stored up to one year, as long as the storage conditions are "adequate" - ie the containers are full to minimise exposure to air, tightly capped, out of direct sunlight, and under 27°C.

underground tanks at servos don't even fulfil those requirements. And vented petrol tanks in cars that get nice and hot sitting in the sun and cool down again at night certainly don't, so the fuel deteriorates much faster than these optimum storage conditions in Shell's literature.

Link to comment
https://www.sau.com.au/forums/topic/138836-petrol-expire/#findComment-2586384
Share on other sites

The deterioration of fuel is or can be brand dependent. If you read any of the links in my previous reply, it appears that the length fuel can be stored also relies on the preservatives each company uses to increase the shelf life of their brand. I don't know which ones are best, but I wouldn't trust any of them. Its an easy question really: Whats cheapest, a new tank of fuel or an engine rebuild?

Link to comment
https://www.sau.com.au/forums/topic/138836-petrol-expire/#findComment-2586431
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • R34DE as in R34 with an RB25DE? So did you get this? Or you planning to?  I'm not really sure what you're saying. 
    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
×
×
  • Create New...