Jump to content
SAU Community

Apexi Power Fc Boost Controller

Nic19

By Nic19,
in Engines & Forced Induction

 Share

Recommended Posts

Cubes Grand Master

Cubes

Posted
Posted
electronic units have brains

Some do.

Some are nothing but a glorified manual boost controller. i.e simply set a gain and a duty cycle.

The better EBC's 'learn' what duty cycle is required in order to hold a given boost pressure. (AVCR, PFC EBC, Blitz SBC-id, Greedy Profec EO-1 and a few others)

The Jaycar boost controller allows you to manually tune the duty cycle through various rpm points; which can be very handy depending on what your goals are. :D

Cubes Grand Master

Cubes

Posted
Posted

The PFC boost kit is good if you want just a cheap boost kit that holds boost well.

For a higher powered car where you want maximum response the avcr is a better bet as you are able to fiddle with individual gear gain values etc.

Sydneykid Grand Master

Sydneykid

Posted
Posted
For a higher powered car where you want maximum response the avcr is a better bet as you are able to fiddle with individual gear gain values etc.

Simple answer, if I don't want as much power, I don't psuh the accelerator down as far. I don't care how smart the boost controller is, I KNOW that I am a lot smarter.

:P cheers ;)

Cubes Grand Master

Cubes

Posted
Posted
Simple answer, if I don't want as much power, I don't psuh the accelerator down as far. I don't care how smart the boost controller is, I KNOW that I am a lot smarter.

;) cheers :(

Maximum response per gear not less. :P

For a higher powered car where you want maximum response the avcr is a better bet as you are able to fiddle with individual gear gain values etc.

Its not so much an issue with a stock turbo'd car.

Although not considered high powered lol I experienced issues when running the lazy vg30det turbo on my old rb20det.

I was running a I was running a Blitz SBC-ID in Auto mode; learning was done in 4th gear as it should.

First gear just wasn't snappy and didn't reach the boost target; raising the gain value had first gear boost build better not to mention it also reached the boost target but caused issues in the higher gears. I could see an application for the AVCR in this instance.

Sydneykid Grand Master

Sydneykid

Posted
Posted
Maximum response per gear not less. :P

Its not so much an issue with a stock turbo'd car.

Although not considered high powered lol I experienced issues when running the lazy vg30det turbo on my old rb20det.

I was running a I was running a Blitz SBC-ID in Auto mode; learning was done in 4th gear as it should.

First gear just wasn't snappy and didn't reach the boost target; raising the gain value had first gear boost build better not to mention it also reached the boost target but caused issues in the higher gears. I could see an application for the AVCR in this instance.

If the boost controller is allowing the wastegate to open before the boost target is reached, then it's a BAD boost controller. That's either ZERO or 100% solenoid duty, it should be fully open or, in the case of an IEBC, fully closed. Regardless of what gear it is in, it's still a BAD boost controller if that's not the case.

;) cheers :(

Cubes Grand Master

Cubes

Posted
Posted
If the boost controller is allowing the wastegate to open before the boost target is reached, then it's a BAD boost controller. That's either ZERO or 100% solenoid duty, it should be fully open or, in the case of an IEBC, fully closed. Regardless of what gear it is in, it's still a BAD boost controller if that's not the case.

:D cheers :D

Oh Gary Gary Gary.. :w00t:

A boost controller MUST start feeding a little pressure to the wastegate before the target boost pressure is reached. This is the gain value. If it were to be closed until its reached the target boost then slams open it will spike. There's no if's, no buts.

The gain value is to compensate for the slight delay in the wastegate slamming open.

You know this..... :w00t:

Sydneykid Grand Master

Sydneykid

Posted
Posted
Oh Gary Gary Gary.. :w00t:

A boost controller MUST start feeding a little pressure to the wastegate before the target boost pressure is reached. This is the gain value. If it were to be closed until its reached the target boost then slams open it will spike. There's no if's, no buts.

The gain value is to compensate for the slight delay in the wastegate slamming open.

You know this..... :w00t:

Well, yes and no.

Yes, but I thought you were talking about the difference before boost started building ie, when the wastegate should be 100% closed anyway.

And no, these days with the fast acting solenoids, short actuator hoses and a correctly sized wastegate (diameter and spring rate), the opening doesn't have to be that premature. A couple of psi is all you need, and you shouldn't notice it anyway, if you have the timing right.

:D cheers :D

Cubes Grand Master

Cubes

Posted
Posted
Well, yes and no.

Yes, but I thought you were talking about the difference before boost started building ie, when the wastegate should be 100% closed anyway.

And no, these days with the fast acting solenoids, short actuator hoses and a correctly sized wastegate (diameter and spring rate), the opening doesn't have to be that premature. A couple of psi is all you need, and you shouldn't notice it anyway, if you have the timing right.

:w00t: cheers :w00t:

I was sure it was a misunderstanding which is why I explained myself a little further. :D

Even with fast solenoids and short hoses there is still going to be a bee's dick delay; which is where the gain value comes in to it. An attempt; as you know to absorb the delay without noticeably smoothing of the boost curves elbow.

A nice sharp boost curve induces that wheel spin (which can be a bad thing) and that oh so lovely snap in the back we all love.

My fiddling found a gain value that was tweaked as close as possible before spiking occurred had a nice sharp smack in the back when boost came on as one loaded the car up from low rpm. A gain value that was low or not tweaked had a noticeably but not by bugger all smoother feel to the boost snap.

I guess really its all about the driving experience; I'd be very surprised if it made any difference to acceleration performance.

Cubes Grand Master

Cubes

Posted
Posted

Bang for buck you can't go past the Apexi PFC EBC as its dirty cheap from nengun and perfect run etc and as stated above is a duty cycle learning type boost controller.

Personally I would prefer the Jaycar EBC over the Apexi PFC EBC as its more flexible with its only downer being the ugly controller (that you can remove once setup anyway).

For more features (gear gain settings, gear boost settings and a few others) the Apexi AVCR is a good option.

The Mafia Grand Master

The Mafia

Posted
Posted

I want to get the powerfc boost controller kit for a few reasons:

1. Its easy to install, no extra crap on the dash

2. I have a 7psi actuator, and I'm using the $22 boost controller to bleed that to 18psi

3. I want something that I can set at higher boost levels, safely.

4. I want something that won't spike, or shake the shit out of the Boost guage needle.

I like the idea of the powerfc boost control kit being $350 too...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • sinn3r
      R34 Skyline climate control unit transistor

      By sinn3r · Posted

      perhaps i should have mentioned, I plugged the unit in before i handed over to the electronics repair shop to see what damaged had been caused and the unit worked (ac controls, rear demister etc) bar the lights behind the lcd. i would assume that the diode was only to control lighting and didnt harm anything else i got the unit back from the electronics repair shop and all is well (to a point). The lights are back on and ac controls are working. im still paranoid as i beleive the repairer just put in any zener diode he could find and admitted asking chatgpt if its compatible   i do however have another issue... sometimes when i turn the ignition on, the climate control unit now goes through a diagnostics procedure which normally occurs when you disconnect and reconnect but this may be due to the below   to top everything off, and feel free to shoot me as im just about to do it myself anyway, while i was checking the newly repaired board by plugging in the climate control unit bare without the housing, i believe i may have shorted it on the headunit surround. Climate control unit still works but now the keyless entry doesnt work along with the dome light not turning on when you open the door. to add to this tricky situation, when you start the car and remove the key ( i have a turbo timer so car remains on) the keyless entry works. the dome light also works when you switch to the on position. fuses were checked and all ok ive deduced that the short somehow has messed with the smart entry control module as that is what controls the keyless entry and dome light on door opening   you guys wouldnt happen to have any experience with that topic lmao... im only laughing as its all i can do right now my self diagnosed adhd always gets me in a situation as i have no patience and want to get everything done in shortest amount of time as possible often ignoring crucial steps such as disconnecting battery when stuffing around with electronics or even placing a simple rag over the metallic headunit surround when placing a live pcb board on top of it   FML
    • dbm7
      R34 Skyline climate control unit transistor

      By dbm7 · Posted

      Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • 25RBGT
      Got this r31 silhouette flood car to rebuild.

      By 25RBGT · Posted

      First time we have seen lights 
    • Wazmond
      WGNC34 - floor mats

      By Wazmond · Posted

      I think Fitmit had some, have a look on there (theyre Australian as well)
    • soviet_merlin
      Howdy Y'all

      By soviet_merlin · Posted

      Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
×
×
  • Create New...