Jump to content
SAU Community

Recommended Posts

did you end up selling your car?

Had a few tyre kickers, but that doesnt matter. Decided it was time to get off my butt and put the 3.0 litre in. Should be ready in a month.

yeah i fly to mackay every 5 days then back home too brissy working at burton coal, see some skylines not many though, moslty hsv's and fpv's up there...

Tell me about it. And quite a few have large turbos on them.

  • 2 weeks later...
  • 5 months later...

hi all!!!!!!!!! im a makcay resident, and mostlikly seen you around if not you might have seen me, 1994 series one silver number plates 17PSI oh and T wing on the rear just for laughs, would like to organise a weekend race day for the japenies taxies aka r33 skylines ha ha ha at palmyra drags!!!! who would be keen send me a msg and ill organise it. im sick of only one or two others joining me at the monthly drags and its all hsv and fpv pooo! they are nice cars but still Poooooo! any keen? Mafia man im sure you'll be in?

ROFL! Friendly bunch, arent we :rofl2:

gee you two are nice, the reason for adding it to each person is some people dont check this site and if you send it to them as a reply they get an email notice! so unfortunatly yes it was.

OK, so every post you make to this thread is emailed out, only if they have sent email notification for this particular thread. So if they did have email notification setup on this thread, then they will all receive your message seven times. Hence our concern about your eagerness in posting the same message multiple times :rofl2:

Hummmm, well your not in it just for a post count are you... :rofl2:

How about's i fix it... Also point out this thread is 4 years old...

And on another valid point, no one likes Mackay... :D

*Note: The last point may be invalid info

OK, so every post you make to this thread is emailed out, only if they have sent email notification for this particular thread. So if they did have email notification setup on this thread, then they will all receive your message seven times. Hence our concern about your eagerness in posting the same message multiple times :rofl2:

totally was not aware of that so mt appologies 7 times people. ha ha go me! still keen for a drag night for the local r32 r33 r34 gts or gtr, hence so many posts, as i have been to the drags a few times but seen very little skylines out racing.

totally was not aware of that so mt appologies 7 times people. ha ha go me! still keen for a drag night for the local r32 r33 r34 gts or gtr, hence so many posts, as i have been to the drags a few times but seen very little skylines out racing.

Yeah dun worry about us, we're all a bunch of cynical bastards, good to see you are motivated to post! If you are ever passing through Rocky, gimmie a yell :rofl2:

hey mate, when you reply to this thread, everyone gets the email reply. Not just the person you quote.

I'm keen though, should catch up for a meet.

yea mafia i have try'd a few times to contact you to catch up, i see you mention you do your own tuning as well? what tuner shop you at? and im just looking throught the calander for the next keep the speed of the street meet at palmyra drags, so ill post the next race night for all who are keen to go, and im from brisbane, i recon mackay sucked as well till i learned it has a drag strip 15mins away although only open to public one night a month, and mackay offers great fishing so thats me covered!

ok so next drag meet (keep the speed off the streets) is on the 9th of july any and all who are keen to match up your skyline vs other skylines this will be the night to go, if you know other nissan drivers who dont use this site pass it on and lets have some fun. my personal best is 12.6 at 116mph on 18 inch nangkang tyers so theres a challange there for those who run quicker! gtrs have to start off with hand break on cheaters!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
×
×
  • Create New...