Jump to content
SAU Community

Recommended Posts

hey guys, my RB30DET needs the valve springs changed but its too hard for me to do so i want to pay for someone to do them but none of the well known/big workshops wanna do it due to the fiddliness of it. so i'm looking for a small workshop perhaps, reasonably close to metro adelaide that you persoannly would recommend/let work on your car and wouldn't mind a small challenge.

cheers in advance, Ash!

by the way don't tell me to rip the head off and do them cause i really don't wanna and i've already asked Shaun @ boostworx and he said he wouldn't do it!

I too have rung around all the major Adelaide workshops and they don't want a bar of it.

Rip the head off they say. If you find some one to do it, my plans may change.

heheh don't want to give it a shot yourself after the cam gear install???? :laugh:

Chris Milton Engineering are the blokes who did the work on my head.

They too said to rip the head off. They only wanted $100 to fit the springs up but wouldn't touch it with the head on the car.

Reason being.. A custom tool is required to be made and really doing the springs on these heads is a pain in the arse.

I'll probably end up ripping the head off and have them do a valve grind while its there, its done almost 45,000km's so it could do with one.

pity his workshop is far from reasonably close to metro adelaide :)

Some maps say Gawler is metro. Most say Munno Para is metro so Gawler is "close". :)

Personally being non metro is fine by me :) Means i can get my car in whenever i want!

could give Dave from The Motor Shop a try

i did work experiance with him many many many ma.. well u get the picture

edit

Motor Shop, The

14 Dewer Ave Ridgehaven 5097

(08) 8264 1972

Edited by Madaz
I too have rung around all the major Adelaide workshops and they don't want a bar of it.

Rip the head off they say. If you find some one to do it, my plans may change.

heheh don't want to give it a shot yourself after the cam gear install???? :)

ye, if i can't even get that right who knows what i'd do trying to install these.

Should offer Andrew (sky30) $100 to do them seeing as he's done them before! hehe!

rang motor shop and john moyle race engines, both said they wouldn't even want to attempt it so i then rang rhemac and they said ye we'll give it a go but i wouldn't get much change from $800 (i don't think so). mmmmmmmmmm dunno what to do!

lol @ $800.

Bugger that.

As that horrid saying goes Ash.. Suck and see.

Push the boost in to it and see how she goes. Your springs have been shimmed up where as sky30 and my won weren't.

Bl4ck32 has had no issues on 16psi with his spring shimmed.

So give it a go. :ninja:

Shaun shouldn't charge much for a retune on more boost as it should only take two hrs including cam gears.

As much as you don't want to hear it, if the shops won't touch it without the head off, then I sure as heck wouldn't be trying it myself.

It sucks to have to take the head off, but if you break a spring and do further damage the cash it would have cost you to fix might seem like chicken feed.

If I remember your dyno graph, you should be right to try and save some cash up, as it only looked like a problem right up top (which is not surprising for valve springs).

If you do end up having to take the head off though, I know I'm the sort of person who couldn't put it back on without some tickling.

I know I hate it when the two choices that I have are ones that I think both suck - "she'll be right" or "big cash bummer".

If you do end up having to take the head off though, I know I'm the sort of person who couldn't put it back on without some tickling.

lol thats my problem. I've already had the head cleaned up with valve deshroud and mild in/exh porting, I wouldn't mind doing a little more work to the exh. side of things. :)

Was that price from Rhemacs to re skim the head as well? They do tend to be more expencive but i've always found they do more as well, they don't do things by halves. The price probably included all new gaskets and seals etc. add labour onto that and it's probably not too bad.

Was that price from Rhemacs to re skim the head as well? They do tend to be more expencive but i've always found they do more as well, they don't do things by halves. The price probably included all new gaskets and seals etc. add labour onto that and it's probably not too bad.

All though Ash asked for valve springs to be done without the head coming off the $800 price is probably to cover incase they had to rip the head off. ;)

It is fairly pricey. Definitely worth the work doing mine myself. Miltons only want to charge me $100 to fit valve springs up so I'll have them do it + throw a different set of cams in and maybe a little more work to the heads exh. side. Hell its all apart anyway.

I'm happy with the head work Miltons did on mine last time, there was a noticeable difference before and after by just feeling around, and the main thing. The economy is pretty damn good being close to what the rb20det used to get. I was a tad worred about porting etc as I had heard a few horror story's of it buggering up economy. ;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 馃
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
  • Create New...