Jump to content
SAU Community

Recommended Posts

Hey guys,

After a long week of getting my new power FC installed and got my self a terrific tune at Race Pace it has ended badly. I went to race pace thinking that i had a full turbo back 3" zorst however after reciving my car i was told that my cat was a povo 2.5".. :P .. Whats the point...

so race pace did the best job they could gettin 150rwkw out of my car... yea i know dont laugh... just because the mechanics that put my exhast on are very stupid... and ripped me off..

So as the title states i am looking for a Cat converter im not the ritches guy but i do like spoilling my car.

So what brands should i look for???

i have a R32 GTSt looking for 3" cat.

Thanks.

Link to comment
https://www.sau.com.au/forums/topic/141140-catalytic-converter-what-to-get/
Share on other sites

There are some cheap ones on ebay, I wonder how they would go... surely the straight pipe that bolts in (ie, no cat) would only do good things. They are about $80 on ebay. If you are running a stock one at the moment, its probably very old and blocked, so you'd notice the difference removing it.

This is the cat you want.

post-14974-1162251135.jpg

I think it's made by magnaflow, it's a metal cat. It is classified as a 3.5" inlet/outlet cat, one

side is centred, the other is offset. No flanges on it, and it costs about $400 if you get it wholesale.

There might be a GB on that will get you one cheaper.

The actual cat section is the bit in the middle; the other parts have no material in them and are to expand

it out from 3.5" or whatever your input size is. If your input size is smaller, make an expander :yucky:

I sectioned it back to suit my 4" pipework and external gate's outlet - you could probably put this into

6" pipework if you really wanted (but you would be well outside the manufacturer's designed operating

range then).

Am going to get it emissions-tested; when I do, I'll post the results. Seat-of-the-pants feel is that

this single cat outflows the dual 3" catco cats I had on my last exhaust by a little... but that's only

a feeling at this stage :sick:

Regards,

Saliya

Edited by saliya

metalcat 3" cat. stainless outsite, stainless inside! no ceramic rubbish! $280. form the group buy section but you need to flanges put on it or order one with the correct flanges :D mine performs like I have no restriction in the exhaust at all.

sorry to jump in, but now i'm concerned.

what size does my cat look to be. this is a 3 inch pipe before and after the cat.

thats the standard 2.5 inch compliance cat from when the car was imported.

Sorry to say but its time for a new one.

Yea i have been looking at a magnaflow.. but i might cheack out this one on ebay.. not the straight pipe with a bolt on it though not readdy to pay thousands in fines...

Ay monkeyboy looks like u have the same problem as me.. i renember seeing a thread of this guy selling alot of stuff a little while back and he was sellin 2 magnaflows but i doubt they are as HC as saliya's cat damm..

so might want to have a look...

Edited by Fugi

X-Force 3 inch highlow - Stainless Flanged cat - (Flows up to 570 cfm)

$160 delivered from Just Jap. You cant beat that price. It's a forum special. Usually $199+delivery.

I just ordered one.

here's the link if you're interested.

http://www.justjap.com/forumxforcespecial.htm

Edited by Munkyb0y

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
    • It's amazing how well the works on the leather seats. Looks mint. Looking forward to see how you go with the wheels. They do suit the car! Gutter rash is easy to fix, but I'm curious about getting the colour done.
×
×
  • Create New...