Jump to content
SAU Community

Recommended Posts

(Did a search but couldnt find anything specific)

I took of the turbo heat shield today and in the process screwed up one of the bolts... so i left it off.

i just wanna know if it will make much difference if the heat shield is there or not? i mean it seems like it would be a benefit for the turbo...

anyone left it off and had any problems with melting nearby wires etc?

Link to comment
https://www.sau.com.au/forums/topic/143030-turbo-heat-shield/
Share on other sites

I took mine off when replacing my stock dump pipe with s steel piping...

Haven't had any issues.. the old heat shield looked gross and doesnt do jack...

now i can see s steel piping and it has cooling advantages 4 the turbo :-P

This was on a 33 btw....

Just make sure no air con tubing runs near your turbo area...or well anything ...

If there are wires nearby, you can potentially cook them.

Realistically, you should run a heatshield if possible.

It will keep under bonnet temps down, and in a turbo car this is very important. The hotter things get the less power you are going to make, also if you are not using proper CAI/Airbox your going to be having major heat intake problems

Just make sure no air con tubing runs near your turbo area...or well anything ...

hmmm what do u mean by "near" coz the closest thing to my turbo area is two air con pipes (with mangy insulation)

they are about 20cm away from the exhaust side..

There was a report in one of the later hot 4's issues about this. It seems that heat shields will have a minimal effect at close range to important things i.e- oil lines it seemed heat wrapping and heat shields both did a little bit to help but if you are really worried grab yourself a turbo beanie they rated the best. ;)

the only good theroy I have heard thus far is the beenie to keep the hot side hot...i.e. greatest heat/pressure difference - afterall thats how turbos work..

I had my shield removed and was thinking about what to replace it with...I was thiking a shield..maybe a bennie? where can u gte these from?

turbo bags are by far the best, they keep the heat sealed in the exhaust housing, even after a hard flogging i could work around my engine bay... going more for show with chrome i changed to a heat shield, although it doesnt quite heat "as" good, if made properly it still works great... the difference is and magazines have agreed, is that the turbo bag can directly touch components and can sit directly on the turbo itself, where as the heat shield must sit around 2-3cm off the exhaust housing itself so heat doesnt trvel through the metal...

in my situation it is a high mount, not low mount, but in either appication id recommend heat wrap and some form of heat shielding wether it be bag or metal plate

but the bag is the better item.

ben...

thanks everyone for ur input - i dont really get why a max temp difference across the turbo makes it perform better... unless it has something to do with the design tolerances.

I have a bonnet scoop pretty much directly above the turbo so it has cool air forced down on it whilst driving.... guess ill put the heat shield back on or get a beanie.

is this a good turbo beanie?

http://www.agpturbo.com/product.php?produc...=257&page=1

lol

but seriously - wheres a good place to get one from?

I still have my heatshield in my boot. A couple of wires ran close to the turbo but I just relocated them. I tried to put the shield back on but some of the bolts just wouldnt budge so I didnt bother. That was a couple months ago now and thus far no issues.

the turbo blanket insulates the exhaust side to retain the heat.. this has two benifits...reduce engine bay heat (although its probably quite hot anyway) and reduces radiation loss from the turbo...why?

turbos work on heat and pressure and the conversion of kinitec energy to make the turbine spin. Once well known example is wacking on a 3" zorst.. it gives greater pressure delta and allows quicker spool and more boost total...as heat is also another important energy source...keeping the temp high in relation to the zorst temp helps produce a greater pressure difference and hence more flow..more flow..more spool..morse boost...anyway thats my basic physics understanding from the top of my head...so correct me if i'm wrong some1.

But i do notice Garret for example warn against use of the blankets in garage enviroments for BB turbos...not so much for water cooled ones...not sure what they are on about exactly.

te one of these....

http://www.horsepowerinabox.com/HPIAB2/category60_1.htm

the turbo blanket insulates the exhaust side to retain the heat.. this has two benifits...reduce engine bay heat (although its probably quite hot anyway) and reduces radiation loss from the turbo...why?

turbos work on heat and pressure and the conversion of kinitec energy to make the turbine spin. Once well known example is wacking on a 3" zorst.. it gives greater pressure delta and allows quicker spool and more boost total...as heat is also another important energy source...keeping the temp high in relation to the zorst temp helps produce a greater pressure difference and hence more flow..more flow..more spool..morse boost...anyway thats my basic physics understanding from the top of my head...so correct me if i'm wrong some1.

But i do notice Garret for example warn against use of the blankets in garage enviroments for BB turbos...not so much for water cooled ones...not sure what they are on about exactly.

okay dont take this personally but that doesnt make sense - the turbo essentially uses the energy of a hot, fast moving gas to spin a turbine. The key principle is that the exhaust gas is moving with a high velocity out of the engine, through the turbine and out the exhaust. Sure, the temperature of the actual exhaust gas affects the turbo's performance by the fact that a hotter gas has more internal kinetic energy and therefore more energy to spin the turbine... but the actual temperature of the turbo doesnt increase its performance - well not as u explained it.

unless as i mentioned/asked before - the turbo's design tolerances are optimal for a certain "hot" temp range - meaning that it just functions better when its hot.

in summary, keep as much hot air inside the exhaust housing and dump pipe!

theres many theories with turbo bags how they are no good, i cant see whats wrong with a quality made one, with a quality turbo, ive seen a fair few and over years and years of abuse on tracks never a fail.

i got mine locally in wollongong, but check out www.gcg.com.au although they might be slightly $$$

ben...

okay dont take this personally but that doesnt make sense - the turbo essentially uses the energy of a hot, fast moving gas to spin a turbine. The key principle is that the exhaust gas is moving with a high velocity out of the engine, through the turbine and out the exhaust. Sure, the temperature of the actual exhaust gas affects the turbo's performance by the fact that a hotter gas has more internal kinetic energy and therefore more energy to spin the turbine... but the actual temperature of the turbo doesnt increase its performance - well not as u explained it.

unless as i mentioned/asked before - the turbo's design tolerances are optimal for a certain "hot" temp range - meaning that it just functions better when its hot.

Yeah. Keeping the exhaust gasses hotter improves their flow out the exhaust.

The reasons behind this are fairly complicated and have something to do with gas flow and fluid dynamics. Something not many people here would be qualified to post about in detail...

okay dont take this personally but that doesnt make sense - the turbo essentially uses the energy of a hot, fast moving gas to spin a turbine. The key principle is that the exhaust gas is moving with a high velocity out of the engine, through the turbine and out the exhaust. Sure, the temperature of the actual exhaust gas affects the turbo's performance by the fact that a hotter gas has more internal kinetic energy and therefore more energy to spin the turbine... but the actual temperature of the turbo doesnt increase its performance - well not as u explained it.

unless as i mentioned/asked before - the turbo's design tolerances are optimal for a certain "hot" temp range - meaning that it just functions better when its hot.

It is a common misconception that the exhaust turbine half of a turbo is driven purely by the kinetic energy of the exhaust. While the kinetic energy of the exhaust flow does contribute to the work performed by the turbo, the vast majority of the energy transferred comes from a different source.

Exhaust exits the cylinder at high temperature and high pressure. It gets merged with other exhaust pulses, and enters the turbine inlet - a very small space. At this point, we have very high pressure and very high heat, so our gas has a very high energy level.

As it passes through the diffuser and into the turbine housing, it moves from a small space into a large one. Accordingly, it expands, cools, slows down, and dumps all that energy - into the turbine that we've so cleverly positioned in tho housing so that as the gas expands, it pushes against the turbine blades, causing it to rotate.

The amount of work that can be done across an exhaust turbine is determined by the pressure differential at the inlet and outlet. Higher outlet pressure, lower pressure differential, less work, less boost...hence why we like to wack on better free-flowing exhausts.

So why a blanket...my assumption is to get a better temp. differentail accross the inlet and outlet...for the reasons stated above and keep the gas in a high energy state..why?? for any1 who has done basic physics you can answer that one!

maybe you should read it again...its not the temperate mate, its the temperate and pressure difference that helps the turbine spin. However the point is, if you retain the heat with a blanket...the air inside should be hotter and buy your own admission this will help....

if the turbo is hotter how will the actual exhaust gases be hotter? its coming from the engine and spends 1 millisecond in the volume of the turbo - after which it may be 0.1 deg hotter but thats not going to matter since the gas has already done its work.

The larger exhaust works to increase the speed of the gas because there is a larger volume for the gas to expand into as it passes through the turbine - nothing to do with the temperature (except for the fact that the gas will be cooler due to the expansion).

there would be no reasonable way to make the exhaust gas hotter since it gets its heat from the compression and combustion within the engine cycle.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...