Jump to content
SAU Community

Recommended Posts

Items:

I want used cooking oil.

Extra Info:

If anyone works in or knows of people with a fish and chip shop I am after their used oil.

Initially am after 30- 40L but will be after a constant supply if plans work out.

Contact Details:

Contact Greg on 0412075359 or PM.

Price and price conditions:

As close to free as possible.

What the heck are you planning to do with used cooking oil may i ask =P I once saw this tv show where they built this engine that ran on used cooking oil and they did exactly

the same thing (go around to fish and chip places asking for used cooking oil =P)

Run a diesel tractor off it. All ideas at the moment.

I wouldn't mind a 32GTR either.

If I could find an immaculate one, I would consider a swap with mine and some cash obviously.

i knew it all along.....jelous :D maybe all my insults have finally made you crack. ill swap ya 32gtr $10 your way and a coupon for a free upsize at mcdonalds

moving onto the topic at hand.

im after the black backing that go's between your speedo dials. dont need the whole thing as my dials are find n dandy, just had a dumb car theif break the black surrounding part a lil as pictured bottom left in this pic.

post-31501-1212503510_thumb.jpg

o and it must be gtr or possibly gts4 as i have a gts-t 1 in now and it blocks the 4wd light n has its speedo reseting hole in a different spot making it look ugly in my dash :( lesson learned never take car to that workshop again.

Edited by Inline 6
i knew it all along.....jelous :D maybe all my insults have finally made you crack. ill swap ya 32gtr $10 your way and a coupon for a free upsize at mcdonalds

You went too far, I hate Maccas.....you had me at hello!!

im after the black backing that go's between your speedo dials. dont need the whole thing as my dials are find n dandy, just had a dumb car theif break the black surrounding part a lil as pictured bottom left in this pic.

Try one of these sunshine

t0008.jpg

Im after one of the following styles of wheel as a set of 4

R32 turbo stockies

R33 / S14 stockies

R34 stockies

or any other set of 15" or 16" alloy wheels with 5x114.3 pcd that are able to be used in a load rated application (ie car trailer). Will even consider ford alloys if anyone has a set (not accepting steelies/interceptors)

Not fussed on condition of tyres (they dont have to have them either). Going to have to buy some LT rated tyres for them anyway

Looking to have a set within the next 3-4 weeks max, as my trailer is due to be assembled in 5 weeks time

PM me, email me or drop me a message (with your name) to my mobile: 0409 049 299

Cheers

Matty T

Items:

factory r32 coupe side skirts in either black or silver (not gunmetal), factory r32 rear bumper in silver, may consider cheap after market bumper or skirts

Extra Info:

prefer in good condition no cracks faded paint etc

Contact Details:

pm me or txt me on 0447490437

Items:

factory r32 coupe side skirts in either black or silver (not gunmetal), factory r32 rear bumper in silver, may consider cheap after market bumper or skirts

Extra Info:

prefer in good condition no cracks faded paint etc

Contact Details:

pm me or txt me on 0447490437

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...