Jump to content
SAU Community

Recommended Posts

Hi guys,

Looking at new rims and tyres. Wanted to ask everyone a good place to go in Perth that has good service and pricing.

Know of a couple of places but wanted to ask everyone on here.

Wheres the best place in Perth?

Edited by Onthehunt

New operation... ROLL RIGHT TYRES in Jonndlaup... Guys name is Stanley.

Was put onto him by a friend who is the FEDERAL tyre wholesaler... great guy and really freindly... not to

mention did a great job (not rough so takes care of your rims) and prices are very good.

hey

my uncle Shane Curgenven is the manager of Goodyear Tyre and break Williton, he should be able to do a good deal on rims and tyres, plus he is the state rep for yokahama poformace tyres so he might be able to get a deal on them for you to.

thanks kenny

My mate manage Beaurepair in Melville,

call in and ask for Yang, he will give you the best deal available.

I wouldn't recommend any one esle in Perth, not because I know him but because he know his stuff.

go and just ask for a quote, doesn't hurt.

hi guys,

thanks for places will follow up tomorow when open.

looking at either 17" or 18" but not sure. is there much difference in weight and performance?

found the gmax energy wheel. scanned a pic of the brochure.

Someone said 18x8.5 at the front might make the steering too light so would it be better to go 7.5 at the front? I am thinking of 9.5 at rear and most likely 8.5 front.

any ideas?

cheers

post-32581-1165124785.jpg

Edited by Onthehunt
so long as you dont get crappy bling bling rims they make skylines look like pieces of sh**

hey gary,

yeh i agree dont like em at all.

i have added a pic of wheel. dodgy scan but does the job. what u think?

  • 6 years later...

JPC have always had a good selection of jap rims, in many sizes and offsets and given me good service & prices! Give Rob a call I'm sure he can hook you up..

Address

Street: Unit 1, 35 Oxleigh Road

Postcode: 6090

City: Malaga

State: Western Australia

Country: Australia

Contact

Telephone: +61 (08) 9248 8865

Fax: +61 (08) 9248 8862

E-Mail: [email protected]

Website: http://japaneseperformancecentre.com.au

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...