Jump to content
SAU Community

Recommended Posts

hey all

ill inform you about the crisis i went through

i was driving down one of the streets in wa...

I WAS HITTING 3 PSI in 3rd gear when i heard a loud pop noise on the drivers side...

just then all my light when on battery, oil level, water temp etc my power steering failed and my brakes woundnt work.... i then quickly pulled my car onto a back street and stop and tried starting it again... it started by then it would just turn off.... and it keep doing it.... it also is blowing out black smoke...

can some one help me and give me advise on what it can be please.......

cheers

jason

Link to comment
https://www.sau.com.au/forums/topic/144949-car-engine-blown-i-think/
Share on other sites

it started by then it would just turn off.... and it keep doing it.... it also is blowing out black smoke...

There's ignition, there's fuel.... Blowing black smoke indicates a gross inlet leak.

I ignored the 3psi fact after I read ----

power steering failed and my brakes wouldn't work
"Fuel pump or fuel lines. No fuel = no go!!!

Warning lights on, brakes and power steering is only from the engine not running. They all need motor running to work properly."

What he said!!!

it also is blowing out black smoke...

black smoke = plenty of fuel.

when my cooler pipe came off i was still able to drive for another few hundred meters until i could find a place to pull over.

but the symptoms are there for a cooler pipe. "it started by then it would just turn off.... and it keep doing it.... it also is blowing out black smoke..."

When it happened in mine after I put my front mount on the car puffed out a big cloud of black smoke and struggled to idle. It gave me a scare as it had never happened to me before. Popped the bonnet and found the hot pipe had come off.

Cheers

Chris

Edited by alphanumeric

and then when the pipe is put back on, just hope that the plugs aren't fouled!

that's what happened when i blew off a cooler pipe.. had to change the plugs to get it to run again... (they were due for a change anyway and i had them there to change that week)

I've had mine let go.. I think its let go on every one who works on their car some time or another.

I was in a rush to take the car for a spin with the new turbo on it. :P

Completely forgot to do up the ic pipe to cross over hose clamp. Started to accelerate lightly, it may have hit 5-7psi or so and BANG!!! nothing, no acceleration. I dipped the clutch the car lumped over for a sec and died.

Tried to start the car; it would start then stall, wouldn't even idle.

Popped the bonnet and saw the ic pipe sitting half in the rubber half out.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...