Jump to content
SAU Community

Epa And Zorsts

khunjeng

By khunjeng,
in Victoria

 Share

Recommended Posts

khunjeng Veteran

khunjeng

Posted
Posted

ok I got my notice and got tested:

Hi-Flow Cat, mid muffler + hot dog + HKS Super Dragger = 94dB

Reverted to a stock system (cat back) 87dB.. was quiet as...

So...it appears you would be close to the 90dB limit with a stock zorst + cannon...I assume most people have hi-flo cats etc

To assist others, what results has every1 else got on the test?

Link to comment
https://www.sau.com.au/forums/topic/145112-epa-and-zorsts/
Share on other sites
sloe-32 Collaborator

sloe-32

Posted
Posted

I also recieved an epa notice the other week for my exhaust. I was told by a tuner that if you buy about 10 metres of steel wool and jam down the exhaust, u'd surely pass. Then after that, just fang it on boost and inevitably, the steel wool should shoot out the back. I'd have to do this for the fact that i have an ECV welded where the diff sits, thus not being able to change exhaust systems easily. Has anyone tried this trick?

Link to comment
https://www.sau.com.au/forums/topic/145112-epa-and-zorsts/#findComment-2711096
Share on other sites
Jamezilla Grand Master

Jamezilla

Posted
Posted

From my run in with Office Steve Austin and his bionic hearing...

Fujitsubo Super TI cat back - and when I say 'cat', I mean a pipe shaped like a cat, and when I say shaped like, I mean it looked like a pipe. Standard front/dump.

99dB - wooh!

Put a GTSt stock system and cat on, was a delightful 88dB

Link to comment
https://www.sau.com.au/forums/topic/145112-epa-and-zorsts/#findComment-2711104
Share on other sites
700HP-GTR33 Mentor

700HP-GTR33

Posted
Posted

3"cat ,1 foot resinator :w00t: ....mid muffler :wave: and hot dog :) 95dba.

Had to get a new muffler and swapped it for the hot dog then it was 90dba at 5300RPM(RB26).

The test is flawed because the Muffler joint that tested it with the new Muffler,(which dropped the size to 1.5 inch.)told me at 3800 RPM he had me at 97dba ;) .So much for the EPA really not knowing shit about imports.

Link to comment
https://www.sau.com.au/forums/topic/145112-epa-and-zorsts/#findComment-2711728
Share on other sites
khunjeng Veteran

khunjeng

Posted
  • Author
Posted

haha a few classics...

yeah so it seems my theory about stock zorst + cannon will probably be over..

which means...basically the whole world of import drivers are over - man I was looking at my stock on the car...looked so sad...was was quite overcome..

just wait for the new twin cannon system I just designed...should be on by the end of the week.

Link to comment
https://www.sau.com.au/forums/topic/145112-epa-and-zorsts/#findComment-2711741
Share on other sites
R31Nismoid Grand Master

R31Nismoid

Posted
Posted
Just wondering, are you testing it at ~4000rpm?

well i doubt it, thats not where they are to be measured.

It all changed about... umm... 18 months or so ago :laugh:

RB20 is 4200 or 4300

RB25 is testing @ 4600 or 4800

RB26 is 5200

The RB26 figure is right, i've checked it. But the others im not sure about as i cant remember.

Been just over 12 months since i've been to the EPA, soon to go back though

Link to comment
https://www.sau.com.au/forums/topic/145112-epa-and-zorsts/#findComment-2712063
Share on other sites
mr_crust Experienced

mr_crust

Posted
Posted

mate of mine got done is his VP SS and racked up 129db , since then the car has been sold.

but the test must be done in an open area, the testing peice must be on a 45degree angle , 1metre away from the exhuast.

another close mate got done in his integra with a stock exhaust, all he had was a tip and they shoved the thing right infront of his exhaustand he went over the limit

Link to comment
https://www.sau.com.au/forums/topic/145112-epa-and-zorsts/#findComment-2712783
Share on other sites
700HP-GTR33 Mentor

700HP-GTR33

Posted
Posted

The calculation is worked out on the RPM using the following method.

Power of car x(by) 3/4 =RPM of test.

I think by memory also.....no turbo rotary(RX) can pass the test because RPM of there test is like at 7000 :ninja:

Link to comment
https://www.sau.com.au/forums/topic/145112-epa-and-zorsts/#findComment-2713066
Share on other sites
700HP-GTR33 Mentor

700HP-GTR33

Posted
Posted
come on guys it's so not hard to find the LEGISLATION on the internet.

speculation is hopeless.

http://epanote2.epa.vic.gov.au/EPA/Publica...;FILE/317.1.pdf

edit: nissan engines Page 63

My computer nearly crashed....please....don't open it :D .

If it is that long....it has no worth to me.... :D

Link to comment
https://www.sau.com.au/forums/topic/145112-epa-and-zorsts/#findComment-2713893
Share on other sites
khunjeng Veteran

khunjeng

Posted
  • Author
Posted

its 4800rpm for the RB25...you could have just asked...I got it tested 2 times this week...

twin system in the mix...I'm getting my V2.0 system tested by my mate just to see what it does with silencers and without..

Link to comment
https://www.sau.com.au/forums/topic/145112-epa-and-zorsts/#findComment-2715315
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      I put another 2 layers of putty and still getting pinholes. Think i might either try the filler first then putty or just leave the little specs of guidecoat as is and get primer to fill it in. I think i misread understood what you said above when you said my glazing putty wasnt enough for the size of the area. I thought you meant 1 coat and i needed to. But i think what you meant was that I needed filler first? I also went a bit too far out the repair area as my spreader is a bit large.
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      You do sorta. In my instance they were little specs and I didn't even think they'd be pin holes but it all makes sense now. Huge learnings there!
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      Ah ok that makes sense and it's where i think i went wrong because before when i put filler then putty, i didn't have this issue and now i do because i only put 1 coat of putty. Thanks for that heaps man, it's a good way to put it! With my putty I'm using the dolphin glaze which i just saw it says finishing putty lol. I didnt put filler cause it was a shallow area but i see what you're saying. Also I'm an idiot, i just realised that while i put new putty there are pinholes! I probably saw it before and ignored it for whatever reason. I think because i thought putty is used to fill pin holes that itself wont make pinholes but that's incorrect of course. I feel silly now haha. ok I think I know what to do next. Thanks man!
    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      Yes correct, the guide coat is showing low spots, in this instance the low spots are pin holes. I agree wetting the areas makes it more visible (but you can see it's there before you wet it as well lol).  Once the panel is flat, the guide coat will be gone  
    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      I wouldn't do it outside, the contamination landing in the paint, the wind and a million other things will drive you crazy.     That's a way too big of an area to use your single stage putty on.  Pretend it's all filler and those pin holes appeared, you'd then use the putty on those pin holes.  They are still pin holes, hmm I expect a few coats of high fill primer could deal with those. 
×
×
  • Create New...