Jump to content
SAU Community

Recommended Posts

Hi all,

Got an R33 Turbs... I've rebuilt the engine and put in an Exedy clutch, etc... forgies and all the rest of it... the problem I'm having is at between 1500rpm and about 1800rpm under a bit of load, I get this nasty vibration that shakes through my car. I can feel it on my foot but not so much through the gear stick. It the same noise that you would get if you had 2-3 heat shields all loose!!

I've been told things like, timing, drive shaft needs balancing, etc.. I've checked every freakin nut and bolt and can't see anything loose!

Any ideas????

Link to comment
https://www.sau.com.au/forums/topic/145394-weird-vibrationnoise-on-low-revs/
Share on other sites

Hi mate, I've got exactly the same thing - funnily enough I've got an exedy clutch in there as well, and searching this forum has netted a few other exedy owners who've had similar issues in the past...hmmmmm.

Wish I could definitively tell you what causes it, Nissan had a look at it for me when I had my major done last week, they agreed that it was the clutch or drivetrain, other ppl have also mentioned tailshaft specifically (not being indexed correctly or something?)......

Edited by RaseR

hhmmm..... very interesting. I can't see why our Exedy clutch's would caus this. I had everything balanced and I tourqued everything up to spec... very weird...

This is killing me here... It has to be the drivetrain, surely...

Another question for you, do you get any other weird noises that seem to be clutch or tranny related?? Like a bit of a low pitch whining noise on idle? My car runs like a dream but these noises really bug me...

If there is anybody out there who had the same problem, expecially if you have an Exedy clutch, please let me know... this is an issue and it needs to be sorted..

Hi mate,

Check this thread for other ppl experiencing the same thing:

http://www.skylinesaustralia.com/forums/in...howtopic=143714

I don't have the whining noise you mention, but I do have another clutch related noise - a lovely chirping sound (sounds like a cricket!) most likely caused by either a worn thrust bearing or input shaft bearing, goes away as soon as you push the clutch in.........Why didn't the previous owner have this replaced when they did the clutch??!!?! It's like a 90c part or something ridiculous like that.

...Hope someone comes up with a solution!

Edited by RaseR

Hi again,

thanks, I'll check it out.... just quickly, you mentioned that you have that cricket noise? I also have that but I did replace my thrust bearing... it's freakin weird... would you believe that I couldn't get the input bearing out!! That's probably what it is... dunno....

if you have any luck finding out what your vibration noise is, lemme know... I'll do that same... I'm starting to think it's a balancing or timing issue....

Cheers....

Hi mate,

Check this thread for other ppl experiencing the same thing:

http://www.skylinesaustralia.com/forums/in...howtopic=143714

I don't have the whining noise you mention, but I do have another clutch related noise - a lovely chirping sound (sounds like a cricket!) most likely caused by either a worn thrust bearing or input shaft bearing, goes away as soon as you push the clutch in.........Why didn't the previous owner have this replaced when they did the clutch??!!?! It's like a 90c part or something ridiculous like that.

...Hope someone comes up with a solution!

I've seen this problem with other cars before (S13 and R33 GTs-t) and both times it was because the clutch was not balanced properly and at that engine speed it would vibrate the hell out of the exhaust brackets that bolt onto the gearbox. Try removing them and see if that helps otherwise get a better clutch :P

thanks for your input mate but i think I'm about to blow your possible theory out the window because my exhaust isn't standard and doesn't actually touch or bolt to the tranny at all.

is that what your talking about?

Just trying to clarify because what you say about the clutch makes sense but if that isn't balanced properly, then where else could the vibration be coming from?

Thanks again, if you have any other ideas, let me know.. I want to solve this problem but if I'm going to drop the gearbox, then I want to make sure I'm not wasting my time... I know it's guess work... sucks...

I actually had my clutch balanced after I brought it from the same place that balanced my other parts....

I hope I've put it all back together properly and there isn't a bolt shaking loose!!! I tourqued the bolts up to spec so they should be fine....

I've seen this problem with other cars before (S13 and R33 GTs-t) and both times it was because the clutch was not balanced properly and at that engine speed it would vibrate the hell out of the exhaust brackets that bolt onto the gearbox. Try removing them and see if that helps otherwise get a better clutch :)

Strangely ive got the same prob. The lovely chirping from the clutch when in neutral and as soon as you even slightly load up the clutch it goes away. I also had the thrust bearing replaced as it was provided with the new clutch/pressure plate. Anything under 2k revs in 3rd gear provides the vibration, but not sure if thats just the engine having to much load on it, or the diff as i have a standard diff which clunks at low speed and can make the car 'hop' if the weight shifts front to rear. Im thinking for me either diff rebuild/new 1.5way or new clutch nismo/excedy. Either way my final 250rwkw power goal will be better served with these other mods i guess.

cheers

Evil

  • 2 weeks later...

Hi guys,

An update, I took my car into a workshop to get some new tranny oil put in.. It seems to have made the vibration a little bit better but not much.

The guys there seem to think it's coming from inside the transmission. My tranny is old and they said something about the bearings needing replacing so I'm now looking for a good tranny, hopefully from an R34!

I will have to find out if they are compatible. Does anybody know if they are???

Strangely ive got the same prob. The lovely chirping from the clutch when in neutral and as soon as you even slightly load up the clutch it goes away. I also had the thrust bearing replaced as it was provided with the new clutch/pressure plate. Anything under 2k revs in 3rd gear provides the vibration, but not sure if thats just the engine having to much load on it, or the diff as i have a standard diff which clunks at low speed and can make the car 'hop' if the weight shifts front to rear. Im thinking for me either diff rebuild/new 1.5way or new clutch nismo/excedy. Either way my final 250rwkw power goal will be better served with these other mods i guess.

cheers

Evil

  • 5 months later...

Just came across this thread in doing a search..

I have the exact same problem as described...

R33 Series 2 RB25DET with 5 speed

second gear at low speed acelerating 1800 - 2000 revs.

I'm unsure wether its standard or heavy duty, feels light & very easy to drive in trafic.

Has anyone on this post found their solution? Its bloody annoying!

Would love to know.

Cheers

Travis

i have an aftermarket single plate clutch and i get the noise too...

(but its barely noticeable, i.e. only when i'm in the driveway next to a brick wall)

put my foot on the clutch and it goes

i have an aftermarket single plate clutch and i get the noise too...

(but its barely noticeable, i.e. only when i'm in the driveway next to a brick wall)

put my foot on the clutch and it goes

thats not the noise we are talking about...

its a full on shudder between 1500-2000rpm while accelerating

full-on shudder sounds like tailshaft issues.

mine sounds like bearings whirring if you try it from too low revs. RB's aren't designed for high load at low revs. get a diesel.

you are all driving in too high a gear, like bimbos who crawl up hills in 4th with their engine pinging its tits off. change down.

Not sure if its the same thing,

im in 1st gear, rev to about 1000-1500rpm and slowly release clutch just above friction point. Car starts to wobble feels like left/right and feels like its going to stall but revs are at 1000+ let go more of clutch and accel and the wobbleness goes away.

Spoke to a gearbox/clutch specialist, said that the flywheel could be out of balance.

Does my problem sound anything similar to yours?

thats not the noise we are talking about...

its a full on shudder between 1500-2000rpm while accelerating

yeah, i know... replying to this...

I don't have the whining noise you mention, but I do have another clutch related noise - a lovely chirping sound (sounds like a cricket!) most likely caused by either a worn thrust bearing or input shaft bearing, goes away as soon as you push the clutch in

:D

  • 9 years later...

hi just came across this thread. ive just fixed this issue.. same deal replaced clutch went an extreme single plate button DSB type clutch and had this annoying vibration. I'm a mechanic myself and didn't want to believe that a bras would generate this bit of virbration. luckily for me I have a 4 post hoist at work so threw it up and had a work mate load it up and found my passenger engine mount had broken as well as my driver side had horribly sagged threw 2 new engine mounts in and whala BEAUTIFUL!!! also added an engine steady dampner bar to help prolong the life of the mounts as well direct the engines tourque to the drive line a bit better 100% worth the $$.. well this fixed my issue so perhaps its something you guys should look at good luck =)

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
    • Wife and I are still looking for a new home. One condition was a large enough garage for a full-size lift in one bay. Now if only we could find something... We've been looking for almost a year now.
    • Thanks everyone for the ideas! Sadly, ramps are a no go for me. With young kids at home, I do most of my work late at night while they're sleeping. Starting the car multiple times wouldn't be a great idea.  I'll go see one of those new long reach low profile jacks and take a couple measurements to see if they will fit.   
×
×
  • Create New...