Jump to content
SAU Community

Recommended Posts

hey guys. wondering if anyone can help me out. i have a 1996 series 2 r33 skyline. me and a mate changed over the front brake pads just before. now it was our first time on a skyline, so we did it slow and all went well. it was all good until i started it up... and the brake pedal is way soft, i can push it to the floor and the car wont stop! so we topped up the brake fluid thinking that would be the problem. but no, ive tried to pump it a bit, and it seems to hold some pressure after 5-6 pumps and starts to brake. but next time i need to brake, there is nothing. ive left the car sit for a hour, drivin it for a hour, and nothing!

what could be the problem? im using the dam handbrake to stop now!

any help would be great.

thanks.

Link to comment
https://www.sau.com.au/forums/topic/145777-brakes-not-working-at-all-o/
Share on other sites

hey guys. wondering if anyone can help me out. i have a 1996 series 2 r33 skyline. me and a mate changed over the front brake pads just before. now it was our first time on a skyline, so we did it slow and all went well. it was all good until i started it up... and the brake pedal is way soft, i can push it to the floor and the car wont stop! so we topped up the brake fluid thinking that would be the problem. but no, ive tried to pump it a bit, and it seems to hold some pressure after 5-6 pumps and starts to brake. but next time i need to brake, there is nothing. ive left the car sit for a hour, drivin it for a hour, and nothing!

what could be the problem? im using the dam handbrake to stop now!

any help would be great.

thanks.

you need to bleed the hydraulic system,

^ Exactly, Bleed your front AND rear calipers,

There are nipples on them that you undo and it will let any air bubbles pass.

I'm sure there is a article on it somewhere, just have a quick search.

Cheers

Josh

the nipples are the lil dome's ontop of the calipers. get your mate to pump the pedal up and then hold his foot down on the pedal then you open the nipple. just dont let your mate go all the way to the floor then repeat this until the brakes return + dont let the reservior run out of brake fluid. For f**k sake dont drive a skyline without brake's jesus!

Edited by dead32

who in their right mind would change pads without bleeding the whole system anyway its part of changing the pads and if you didnt know this you shouldnt have even attempted changing the pads

who in their right mind would change pads without bleeding the whole system anyway its part of changing the pads and if you didnt know this you shouldnt have even attempted changing the pads

You bleed the brakes every time you change pads? I must be doing it wrong as i've never once had this problem and I only do brake fluid when it needs it.

while ur at it get some high temp fluids in. good for cruise and track days.

You mean - high priced fluid which is 100% more expensive for maybe 5% better performance... yeah thats a great idea.

Anyway for the original post, you have got air in your brakes somehow. Air bubbles are a pain in the ass to bleed out sometimes and sometimes you can make it worse if you stuff up something. You can spend a good amount of time getting the brakes back so if you cant be bothered take it to the nearest brake place and get them to use their pump. Costs an hours labour.

You dont bleed brakes wen u change pads, and it isn't part of the service! trust me I was an advisor.

If u need to bleed your brakes everytime u change ur pads then something is wrong with ur system.

Cheers

Josh

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
    • I forgot about my shiny new plates!
    • Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
×
×
  • Create New...