Jump to content
SAU Community

Recommended Posts

Beautiful car. Just curious as to what guard work had to be done to fit 10.5 +20 all round??

Is the clearance any different between a 4 door and a 2 door?

I spent about 8-10hrs on my guard work alone making the car about 25mm wider than stock.

also want to know, also camber specs if you have them please :)

I'll get specs as I've just been playing around with different ride heights and wheel combo's before another alignment.

Don't usually like sedans but well done. Have you thought about a roof spoiler?

How does the taillight cover appear at night?

Tail light cover is just a test ATM, aiming to make something more permanent soon.

Yeah thought about a roof spoiler, but I think it might ruin the clean lines.

Looks tough, love the dish!!

Here's mine just before I pulled it off the road again!!!:

Recently fitted bilsteins to get the height right :)

Also got bonnet struts and carbon radiator infill panel.

gallery_12712_2799_54273.jpg

gallery_12712_2799_39550.jpg

'Bayside' blue.

gtr99vbayside.jpg

considering that we are both in Sydney, I'd be more than happy to pay u take some pics of my australian delivered r32 gtr. Ive always wanted decent pics of my car and your skill set is amazing. Would u be interested?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...