Jump to content
SAU Community

Recommended Posts

so i installed a walbro, but when i pulled the stock pump out it was loose as on the bracket . e.g. the bracket could move around and i literally pulled it out..

so i put the walbro back in like this, but it needs to be fulled right up to even run otherwise it doesnt suck through fuel, and it looses fuel goin around corners... is there some sort of special way they need to be placed in because at the mo it aint good.

Towards the back of the tank you will see the area where the bracket is meant to hook back onto, plus if the above senario sounds rihgt try and get the pickup down as far as you can on the tank in the middle right at the back, this is the lowest point i have found on the tank especially that the fuel suck/pickup point is here for the stock pump i found that originally the bracket was just lose inside the tank, so had to mount back in its original position. Check that out and see how you go, by the sounds of it the pump is facing sideways and not low enough in the tank, hence centrifugal forces will act acordingly, hence not sucking enough fuel.

Cheers

Adam

There should be a metal plate over a plastic plate with two slots cut in it located around 10 inches below the top of the tank.The tabs of the fuel pump mounting bracket slip into those slots.And yes it is a back breaking pain in the arse.

You have to gently tap the big lock ring around with a hammer and plastic drift. Hand tightening is not enough.

Before you do it, make sure the large 'O' ring seal is correctly positioned.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
    • Just like in being 14mm too small (296mm) makes it not fit, being 14mm too big (324mm) it also won't fit. You want to find the correct rotor.
    • @GTSBoy Ok so that was the shops problem...they showed R33 rotors on R34 page and i did not know 296 do not fit(and are for R33) Yes i bought "kit" with rotors and pads. Pads are ok(i have GTT calipers front and rear). They have some 324mm but no 310mm. So i dont know if they would fit. I have 17inch LMGT4s So another question. Can i fit those in the rear or they are just "too" big for that?
×
×
  • Create New...