Jump to content
SAU Community

Serious Help Needed

Shoudi

By Shoudi,
in Engines & Forced Induction

 Share

Recommended Posts

Shoudi Enthusiast

Shoudi

Posted
Posted

Hi Guys

I have an R33 GTST and it is haven some major problems lately.I Installed the Apexi Power FC Last night and I want to take it to get dynoed and tuned but the car is running like shit. It will hunt around every now and then, It surges really bad, it feels like the engine dies and when you accelerate only the turbo opens up and the engine makes a dull machine gun sound and jerks really bad. The RPMS also drop while you accelerate and then the engine kicks back in or sometimes it will drop way down until it stalls itself. For some reason it happens on and off and I'm starting to get worried as the episodes last a minute or two and at the moment it's to hard to drive and it will happen on straights or corners just out of the blue. I was thinking it needs a new fuel pump or it's not getting enough fuel. The car will also only half accelerate, you accelerate but it's like it will hold back.I have also tried resetting the ECU and doing the Idle test. I'm running out of ideas and these episodes started last week before the ECU was put in. What is is? Please help I want my baby to run again

3" cat-back kakikomoto exhaust

Splitfire Di Ignition Coils

Hybrid Intercooler

HKS Pod Filter

Blitz Boost Gauge and Full Turbo timer

Apexi Power FC + HC

Link to comment
https://www.sau.com.au/forums/topic/147420-serious-help-needed/
Share on other sites
Shoudi Enthusiast

Shoudi

Posted
  • Author
Posted
sounds like dieing fuel pump to me.

What pump should I use. Is the Bosch 044 any good? I've read alot of highly modified cars use them. Also how amny is to many or not enough? I've seen some with 2 or 3. Any ideas would be greatly appreciated.

Nabil Rising Star

Nabil

Posted
Posted
What pump should I use. Is the Bosch 044 any good? I've read alot of highly modified cars use them. Also how amny is to many or not enough? I've seen some with 2 or 3. Any ideas would be greatly appreciated.

With your current modifications

stick to a 040 in-tank it will support 500hp and costs about $190.

An 044 is external and will cost more to connect.

PS. Before you fire up the engine can you hear

the pump priming?

Shoudi Enthusiast

Shoudi

Posted
  • Author
Posted (edited)
With your current modifications

stick to a 040 in-tank it will support 500hp and costs about $190.

An 044 is external and will cost more to connect.

PS. Before you fire up the engine can you hear

the pump priming?

Yeah you can for a second or two sometimes

Edited by Shoudi
WazR32GTSt Grand Master

WazR32GTSt

Posted
Posted

my reasoning is...

car works fine

something is changed

car runs like shit

...therefore, the reason the car runs like shit is directly related to what you changed

have you tried putting the stock ECU back in to see how it runs?

my bet is the powerFC not connected properly..

good luck

Warren.

maccattack Proficient

maccattack

Posted
Posted

I had an intermittant problem similar a while ago. Car would stall (almost), then run fine, then be shit again for no reason. Changed everything from AFM's to pump to CAS to wiring etc. Turned out to be the connection on the top of the PFC. Because of the centre bolt, the outer pins would lose contact as the plug rocked back and forward. Put large zip ties around the ends of the PFC and plug. See if it helps.

Shoudi Enthusiast

Shoudi

Posted
  • Author
Posted

It was acting like this exactly 4 days before installing the PFC. I wnet through the half hour idle set up and only a little bit of black smoke comes out but when it plays up a shit load does. It had same problems a week ago with the stock ECU.

Scooby Veteran

Scooby

Posted
Posted
these episodes started last week before the ECU was put in.

so I assume it's prob not the pfc entirely, although the symptoms may have changed a little due to the pfc settings. it sounds like an AFM to me but I don't know what the machine gun sounds are from. if it was making them only after the pfc it might be the ignition settings. either way just go back to the stock ecu and start diagnosis from there at least you have a known start point. use the self diagnostics to see if it's a sensor fault.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R32 GT-R: 4WD Light Turns On After Bumps – Code 19 (ETS Motor) But No Issues Found

      By GTSBoy · Posted

      Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Bireley_32
      R32 GT-R: 4WD Light Turns On After Bumps – Code 19 (ETS Motor) But No Issues Found

      By Bireley_32 · Posted

      Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
    • MBS206
      Starting again

      By MBS206 · Posted

      The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
×
×
  • Create New...