Jump to content
SAU Community

Recommended Posts

After my recent turbo upgrade I have lost the belief of the common

marketing scheme, "bolt-on."

1. So has anyone installed a set of these on their RB25?

2. If so, is there any customizing involved?

3. Do I need a collar set?

4. Will it fit straight on the fuel rail?

5. Will they plug straight into the fuel sensors?

6. Are these side-feed? Because they say they are for R33's

The part no. from Nengun is as follows:

16600-RR543 (yellow)

Setting me back $834.07 delievered

Thanks Heaps :(

Cheers,

Bill

Link to comment
https://www.sau.com.au/forums/topic/147587-nismo-555cc-injectors/
Share on other sites

1. So has anyone installed a set of these on their RB25?

Yes - bought them from Greenline

2. If so, is there any customizing involved?

No

3. Do I need a collar set?

No

4. Will it fit straight on the fuel rail?

Yes

5. Will they plug straight into the fuel sensors?

Sensors?! They plugs are compatible with the stock ones

6. Are these side-feed? Because they say they are for R33's

Yes, sidefeed and high impedence - no resistor packs or anything. Its like changing the stock ones for other stock ones.

You will NEED a tuneable ECU though, I dropped the base fuelling by a LOT and it still fouled the plugs straight away! They flow heaps more than the stockers.

  • 2 weeks later...

I was speaking to a tuner (Adam) at JEM and he advised me to stay away from nismo injectors as they are hard to fine tune and was also told by BEL Garage to stay away from them too...

What are your thoughts guys?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hopefully it ends up being something manageable, like a hone, rather than a full bore—it would be a huge relief if it’s not as bad as it looks. Hang in there; these setbacks are annoying, but it sounds like you’re handling it as smartly as possible.
    • At the end of the day, it’s all about understanding the odds and being comfortable with the potential cost, whether it’s horsepower on a build or chips on a roulette table. And I have to say, the Laine example made me laugh—some people really do embrace that carefree, “roll and see” attitude!
    • Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
×
×
  • Create New...