Jump to content
SAU Community

Recommended Posts

Hello,

I needed a new (used) car and came across this ad:

R33

(Yes, I'm in the UK)

I liked the car, because this one is not modified and has not any embarrassing mods or spoilers.

The price is 12,500 AUD.

Though the price sounded a bit steep to me I had a look at the car.

Had A Look At The Car

In reality it didn't look that gorgeous anymore, but I still liked it.

I did some checks on the car, and followed an advice I got to verify the year:

The year of manufacture can be found by looking at the front seatbelts, near the floor mounting point. There is a fabric tag with the seatbelt specifications and the year of manufacture sewn onto the webbing.

So I checked the tag and it said 1993! ;)

I pointed this out to the seller, and he said that the seatbelt might have been replaced ..

I think that's quite a far fetched story, but are there any things apart from the tag to tell the year?

I checked many Skyline pictures, and all with the year 95 seem to have an airbag.

There's a number on the firewall where the engine sits and it says:

ECR33-002864

If this is some kind of serial number, it sounds pretty low to me and would support the 1993 tag year.

Hmmmmm .....

Is there any check I can do on the number?

I still like the car, and the engine made a good impression on me.

I'm a complete beginner with Skylines and any help is highly appreciated.

Thanks for the help!

Greetings from London!

Link to comment
https://www.sau.com.au/forums/topic/147634-how-to-tell-the-year-of-a-r33/
Share on other sites

Car is a '93 or '94 model ;)

- Seat belts are manufactured by another business, so they can be done in advance.

- The engine has the coil igniter modual, on the top, at the rear (near the firewall), which only came out in '93 or '94 cars.

- Has the S1 rear spoiler

- No airbag

"The price is 12,500 AUD.

Though the price sounded a bit steep to me"

Hi,

I would have thought $12500 for an R33 with 69000km on the clock, was little on the too good to be true end of the scale if anything...

Damien

Edited by ShylineR33
"The price is 12,500 AUD.

Though the price sounded a bit steep to me"

Hi,

I would have thought $12500 for an R33 with 69000km on the clock, was little on the too good to be true end of the scale if anything...

Damien

No, it represents the upper limit for such a car in the UK and I'd only pay the amount for a 95 in mint condition.

As for the milage you should consider if such a low milage is realistic for an 11 year old car.

The car in the link (true 95) below is at 13,000 AUD and also at the top range of prices.

Besides note that this is not a GTR!

GTRs is what people want, so the price is higher.

Cheers

Edited by Torques
Car is a '93 or '94 model ;)

- Seat belts are manufactured by another business, so they can be done in advance.

- The engine has the coil igniter modual, on the top, at the rear (near the firewall), which only came out in '93 or '94 cars.

- Has the S1 rear spoiler

- No airbag

:D

Thanks, I agree ... the seat belt could be made in advance ... but 2 years?

So much harder evidence seems to be the spoiler / airbag / coils.

What does S1 mean? And when came the 'new' spoiler exactly?

Can I do any research regarding the number on the firewall?

If you look at this one, it seems to be a true 95 model and I'd pay the price for it.

True 95

:(

Thanks, I agree ... the seat belt could be made in advance ... but 2 years?

So much harder evidence seems to be the spoiler / airbag / coils.

What does S1 mean? And when came the 'new' spoiler exactly?

Can I do any research regarding the number on the firewall?

If you look at this one, it seems to be a true 95 model and I'd pay the price for it.

True 95

that one looks like a S1.5 - S1 front with S2 wing and the clear skyline boot garnish

the higher wing came on the S2 models, and on the S1.5 models

S1 is series 1 - info can be found here

S1.5 is series 1.5 - info can be found here , this is basically a S1 with the S2 wing and engine.

S2 is series 2 - info can be found here

more info on model differences can be found here

it is mainly cosmetic changes and standard options, there is other things like the coil igniter module as noted above

you can post the VIN number (number on firewall) in these threads and someone with the Nissan FAST program will check it out for you

http://www.skylinesaustralia.com/forums/in...howtopic=133729

http://www.skylinesaustralia.com/forums/in...howtopic=128496

yeah it looks like a 93 - rear spoiler and steering wheel - but thats how i look at it

what is it bout the steering wheel that differentiates the models? just curious

EDIT: ok realised for myself. its the airbag right?

Edited by Basti

Good morning from the UK!

Wow ... I woke up this morning and was wondering whether there is any reply at all.

:P

Thank you so much for all the information, this is just great!

I knew from the start that the car didn't feel like a 95 model, but the seller was asking the 1995 price for it.

He stressed many times that this is a 95 model...

As for the airbag I read in a wiki that all 96 models have the airbag as standard.

I think with the VIN number I really can nail the seller down on the year.

(Unless he argues that this has been replaced as well)

Cheers!

:)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...