Jump to content
SAU Community

Recommended Posts

Well I sold the GTR early last year to go back to a GTST. GTRs are an awesome machine but since I like doing tracks days regularly it just became too much spending all my money on the car. I really wanted a series 2 33 sedan in manual and I was lucky enough for this example to come up in a yard on the Gold Coast. It needed work as nearly all skylines do but it was pretty clean and very straight so I snapped it up. The Nismo LM GT2 helped a bit too.

First thing I did was roll it straight to Chapman and Chapman as there were a few mechanical things that needed to be addressed ASAP. Had the full major service performed with all the usual things; timing belt, tensioners, water pump, new plugs, all new filters, etc. A few other things needed to be done also; I had the turbosmart boost contoller removed back to stock soleniod, a new sump put on as the other had a dent in it, replaced the exhaust manifold as the existing one was cracked. Mechanically the car was now given a clean bill of health and drove so much nicer. Next I chased down a stock air-box and snorkel and replaced the K&N pod with the stock box and a K&N panel filter, the noise from pod filters shits me, I must be getting old :)

Next I came across a 100mm thick SMIC out of an R34 GTT, brand unknown. Its a huge unit for a SMIC and gave a very noticeable improvement of the stock SMIC. That combined with 10psi from a turbotech boost controller, and the kakimoto cat back the car came with it was now starting to feel like a GTST should.

Next I PM'd Sydneykid and ordered shocks, springs, swaybars and pineapples through his group buy. Best money spent yet, those items combined with my Cusco rear camber arms, Cusco front caster rods and tension rod, Cusco 1-way diff, Nismo front strut brace with brake cylinder stopper, DBA slotted 4000 front rotors and Hawk pads front and rear and Nismo single plate clutch make this the easiest car I have owned to drive in any conditions, whether it be circuit, skidpan, drag, city driving or through the mountains, its a pleasure anywhere.

The car was recently vandalised so it has been fully resprayed thanks to insurnace and has come up very well. Just yesterday I bought a CES split front pipe and a metal cat so I am keen to fit them hopefully tomorrow. Not sure where I will go next, not keen to burn too much more money, the GTR has left some bad feeling with spending alot on a car again, but I am happy with were it is atm. A nice clean, practical, reliable car which I can still enjoy down at the track. . . . .

med_gallery_1841_122_52708.jpg

med_gallery_1841_122_129242.jpg

med_gallery_1841_122_2408249.jpg

med_gallery_1841_122_1793865.jpg

med_gallery_1841_122_573222.jpg

med_gallery_1841_122_77079.jpg

med_gallery_1841_122_225175.jpg

med_gallery_1841_122_162704.jpg

med_gallery_1841_122_372012.jpg

Link to comment
https://www.sau.com.au/forums/topic/147957-series-2-33-sedan/
Share on other sites

  • 2 weeks later...

nice ride, i have a series 1 4dr, and pulled out the stock seats as quick as i could, they are terrible!

nothing a good pair of recaros couldnt fix though :)

Series 2 tail lights for the win, whats it like on the track?

Have been looking for a pair of 33 GTR seats, recaros or brides. . . .which ever comes up first at the right price. Bracing myself with my knees at the track is getting a little annoying :)

So far I am about 1.5 to 2 secs a lap slower then my old 33 GTR V-spec with basically the same level of modification. . . . . Although I think I can narrow that gap a little as my semis where pretty much shagged and I also developed a boost leak during the last outing also which hampered me a bit. I reckon I can get it down to less than a sec different. In the dry GTRs really aren't that much quicker and I certainly use less fuel in the sedan on track days!

So far my best down the quarter is 13.93, that was before I installed the CES front pipe so I am sure I can shave a little off that too as it definately feels stronger now.

Hey Jason, where are you looking for the Bride seats and are they recliners??

Interested myself, but for the coupe, so they need to be recliners.

They are definately recliners, Bride Ergo. They turned up on Friday, should be in by this afternoon if all goes to plan :)

I was lucky enough to pick them up off a guy in the SAU forsale section, they hadn't been fitted to a car yet and came with rails. They do come up every now and then, I have just been checking the forsale section regularly, I just missed out on a pair of recaros before Christmas. . . .

post-1841-1168203479.jpg

  • 2 weeks later...

They were a pest to put in. The rails that came with them were supposed to be the super-low ones but there was nothing super-low about them. Had some custom ones made up and they sit the same height as the stock seats did now, and there is no way they could go any lower. Damn that buldge in the floor on the passenger side!

But apart from that the are a huge improvement on the standard seat, heaps more support and a lot more comfortable thatn I expected. Apart from the extra cost incurred in get custom rails made up I am one happy customer :)

gallery_1841_122_29612.jpg

gallery_1841_122_31689.jpg

  • 3 weeks later...
very nice

love the seats, what were they worth?

Too much :laugh:

I managed to track down one of those Nissan option grill things on the weekend. Have been scouring the for sale section, even the yahoo auction for months, and finally one came up down the Gold Coast. A good excuse to cruise down to the coast for the day. I think they look a little dressier.

gallery_1841_122_8276.jpg

It is a stock colour although after the respray it has come out a little darker than it was to start with..... errrrr, Not knowing exactly what each line is on the plate, chassis and engine are pretty easy, KN6 looks like a likely suspect for the paint code.

Sound like one??

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...