Jump to content
SAU Community

Recommended Posts

  • Replies 6k
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

The easiest and cheepest way was to get it fitted by a workshop (I used Morpowa) because GCG offered a discount if a workshop fit it. The discount payed for the installation and tune.

so it was as simple as, drop the car at Morpowa and they do all the rest?

as your likely to get a new/reconditioned turbo sam, do you have the necessary support mods yet or are they coming?

Im organising a power fc too, injectors should be fine at the boost levels i'll use, im pretty sure ive got an upgraded fuel pump too, but i need to check that for sure :)

i know of one workshop that charged my friend $900 for a turbo install. Is this a resonable price - you dont have to state how much you paid guy just your opinion and other ppls opinion in general.

That sounds a bit expensive. The job is easy and quick enough on an R33. I paid less than that and the job included shipping, new coolant and oil, and time on the dyno to reprogram my PFC.

I guess if it wasnt an R33 then that may take a bit longer.

so it was as simple as, drop the car at Morpowa and they do all the rest?

Yes.

Took nearly 2 weeks (but we did it on the 2nd of January and shipping was a bit slow due to the x-mass new-year holliday rush. I think its about 1hr to remove turbo, 1 hour to install then dyno time.

That sounds a bit expensive. The job is easy and quick enough on an R33. I paid less than that and the job included shipping, new coolant and oil, and time on the dyno to reprogram my PFC.

I guess if it wasnt an R33 then that may take a bit longer.

i think it was a HKS GT2530 on R33, right duc? they require some mods before they fit up

Im organising a power fc too, injectors should be fine at the boost levels i'll use, im pretty sure ive got an upgraded fuel pump too, but i need to check that for sure :)

It would be wise to install injectors aswell.

I have a rising rate reg, and bigger fuel pump but I am limited to 14psi boost because my injectors are already at 90%. With injectors I shoud get over 250rwkw.

shouldn't be anywhere near that expensive unless custom work has to be done. Both times my manifold had been removed it only cost $400 (not quite as big job as fitting a turbo, but damn close).

That sounds a bit expensive. The job is easy and quick enough on an R33. I paid less than that and the job included shipping, new coolant and oil, and time on the dyno to reprogram my PFC.

I guess if it wasnt an R33 then that may take a bit longer.

Unfortunately it was a 33. im sure replacing the turbo was a quite straight forward process even with some fabrication for the oil and water lines if required. The labour did not include any form of tuning. I personally believed he was ripped off.

i think it was a HKS GT2530 on R33, right duc? they require some mods before they fit up

yeah it was sam, you know the guy im talking bout. I feel sorry for him. Damn workshops prey on those who dont know any better.

Hey guys

           After reading all of this... Do you reckon I need more stuff for my car. e.g. upgrade fuel pump,etc.. I've got the power fc, avcr, frontmount, ..

what next? Or will it be ok?

Cheers

Iceduck:)

Have you got all that gear installed yet duck?

yeah it was sam, you know the guy im talking bout. I feel sorry for him. Damn workshops prey on those who dont know any better.

Thats weak, hey. Just make sure we never take any business there. Yeah, for sure they ripped him off, they probably made about $450 an hour out of that job.

there are certain aspects that they are good at what they do but it just seems that if they can take advatage of you they will.

They do anything to make an extra dollar. Can you PM me the name of the place? i forgot already.

It would be wise to install injectors aswell.  

I have a rising rate reg, and bigger fuel pump but I am limited to 14psi boost because my injectors are already at 90%. With injectors I shoud get over 250rwkw.

definately agree. aftermarket injectors i.e 550cc variants wouldbe a good investment. I believe rising rate regulators are just a band aid. AI'd rather my duty cycle to be lower, more opportunity to get the most out of your turbs.

definately agree. aftermarket injectors i.e 550cc variants wouldbe a good investment. I believe rising rate regulators are just a band aid. AI'd rather my duty cycle to be lower, more opportunity to get the most out of your turbs.

Yeah, injectors are on my list. right after i save a bit more money, these mods are a big drain on the bank account

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Nah. Was just wondering if you were having a small stroke or if there was some slur/gaf/inside joke that I wasn't aware of.
    • That was a fark up, it's Salamanca Place I was thinking of. And now I'm curious as to what potential slur/gaf I have caused with Salamander Road, ha ha!
    • Actually everyone on the roads was really well behaved. The only person that did any minor tailgating was a local hoon in a Turbo Focus. Unfortunately we weren't going the same way so there was no grand initial D touge battle. Lots of people pulled over and let me through. The amount of "Hey man nice car, omg skyline, nice 34 man woo" was suprising. Like really suprising. Like almost annoying. My partner was obviously surprised, she'd never seen anyone in the real world point out the car/like the car/want to chat about the car before, so to have like 3 people per day mention it was notable, I could finally say SEE? SOMEONE THINKS THEY'RE COOL. Everyone was also pretty suprised about the weather. Every day was dry and about ~13-14C. Mount Wellington had a sign that said they close the gates at 9pm and I was heading up there at about ~7:30. It was VERY apparent that conditions were getting significantly worse by the minute on the way up and down. The road on the mountain was terrible though, it's no driving road. I have various suspension related questions now. Luckily it was only about 20 minutes from where we were staying to the top of the mountain as said Google maps. We only had the 2 nights in Hobart. We went to the Farm Gate Market though which was really good - And went down to the Hastings Thermal springs/caves down there during the day. I'd definitely be up for going back again, so luckily there's a few more sights yet to see. Didn't get to do the west coast/queenstown/cradle mountain so this was supposed to be a 'scouting' trip anyway of sorts if I were to one day do/take part in/organize a more car-focused trip. As for the boat, it wasn't bad. Well it was bad, but not in the way you're thinking. We did the night trip which leaves at 6:45 (though you have to be there ~2 hours earlier) and arrives the next morning at about 6am. There is nothing to do on the ship. If you plan accordingly and bring a book/tablet/show to watch/charger you can just chill out, take some Travacalm and just sleep through it. The food there is an extremely basic buffet that costs $32 a plate, or $14 for a $3 pizza. The way back we had a travel kettle and a few different types of cup noodles and made our own tea/coffee in the room. This was a far superior way to do it. At the very least book one of the rooms with beds. I guess as we were in the off season we didn't have room mates. You get an option for rooms with 4 beds (2x bunks) or a room with just the two bottom beds. There's also some option for a deluxe queen bed but it's much pricer. We've been on sleeper trains in Asia before so we figured this is similar (and it was)
    • You just gotta be really, really, really clear and decisive with what you want your end product to be. 99% of people who want this conversion aren't "I want to run a 295 front tyre!" so they don't really need the widebody. They just want the OEM body to look a little less dumpy, so bonnet, bar, skirts job done with some camber, stretch, slam. It's when you want that, but then decide to pivot later you get big problems. See also if you're willing to get an all in one fibreglass bar, and you're willing to accept fibreglass problems like cracking the entire item on a driveway, instead of just a piece attached to the bottom, etc etc etc. Decide this all before buyin'.
×
×
  • Create New...