Jump to content
SAU Community

Recommended Posts

hey all

i am going to drop a RB25DET into my R32 GTS4

i guess i have to put a R33 RB25DET ecu and loom in but,

(i know this may sound stupid) will the RB25DET engine bolt up to the GTS4 gearbox?

also with the wiring loom, will everything connect up?

is it a straight forward engine swap?

any info would be sweet

thanks

chris

Link to comment
https://www.sau.com.au/forums/topic/150205-rb25det-conversion/
Share on other sites

Not sure about the R32, but i assume it would be the same as the R33.

It is not just a straight swap. Since the GTS4 has front wheels that also drive, the oil sump is a different shape in the GTS4's RB25DE. This means that only another RB25DE from a GTS4 or an RB26 will do. You can turbo your DE, but I agree, an engine swap would be better. Bit of mucking around, but good luck. :)

You can get a RB25DET that will drop straight in from a Stagea. I'm not 100% sure, but I think they made some turbo 4 wheel drive Stagea's, but they are very rare.

Not too sure on the rest of the details. I think there may be more to it than just the oil sump anyway. Might have to wait for one of the experts to answer. :)

I've got an R33 GTS and I'm doing the same swap. I don't have the all wheel drive issue though, so I'm not sure on all the details.

would it be easier to convert my R32 GTS4 to RB26DETT than a RB25DET?

plus would i really need a complete 4WD stagea front cut to complete a RB25DET conversion to a R32 GTS4?

what parts are needed out of the front cut?

  • 1 year later...

I just got my RB25DET (series 2) and I was hoping you could help me with some questions.

My Skyline is non turbo so it will be a big step with the RB25.

Now then, my first question is about the gearbox mounts, I hear they aren't the same and I will also have problems with the speedo meter. What do you know about this? Can I use the Xmember of the R33 ??

The second is about the harness, everyone that has ever swapped an engine told me that the harness is the most difficult part of the swap. Do you have the diagram of the R32 and the R33 (still can't find it for the R32) and some pointers on how this is done??

Hope to get a reply from you soon

Carlos Rudolph

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...