Jump to content
SAU Community

Recommended Posts

yesterday arvo i was driving down gorge road, put it in 3rd and gunned it basically and it hit 5000 rpm in 3rd and sounded like it was bottoming out...happened for like 2 mins coz i kept trying to see wot happens in high revs. Everything seems to b alrite now but i dont kno...hope its nothin. can sum1 help me with this. cheers

Link to comment
https://www.sau.com.au/forums/topic/150367-r33-revs/
Share on other sites

I HAD SAME PROBLEM 2DAY....DROVE CAR 3 HRS LATER AND WAS FINE...IT WAS HESITATING UNDER BOOST WAS YOURS?

yeh it felt like the car wldnt go over 5000 revs, almost like it was pulling back..but 10 mins or so later it seemed fine....no idea wot was goin on.

Link to comment
https://www.sau.com.au/forums/topic/150367-r33-revs/#findComment-2801063
Share on other sites

It could have been detonating when it is hot.

My other tip would be coil packs on their way out and got hot.

My S15 did this for a while and it turned out to be dirty spark plugs. Mechanic was sure it was coil packs but turned out it wasn't.

I would strongly suggest chucking it on a dyno to find out what is going on asap as you could blow it up quick smart if you don't.

Link to comment
https://www.sau.com.au/forums/topic/150367-r33-revs/#findComment-2801597
Share on other sites

I have trouble in the colder weather with overboosting on the standard solenoid boost control once over 5000 rpm, when it boosts too high it's does the rich & retard trick & it backfires due to overfueling too. I the hot stuff when it's warmer it's ok. I didn't have an issue until my exhaust system was fitted. Going to be getting an EBC soon

Edited by JazzaR33
Link to comment
https://www.sau.com.au/forums/topic/150367-r33-revs/#findComment-2801839
Share on other sites

i spoke to to one of my mates and he reckons coz my pod and catback with my original ecu, nothing has been updated there can sumtimes be a slip in the fuel and air ratio or sumshit.....u reckon this is tru?

by the way car has been fine since hope it stays away, lol

Link to comment
https://www.sau.com.au/forums/topic/150367-r33-revs/#findComment-2809820
Share on other sites

i had the same issues mate, i bought my car stock with 3 inch cat back and K&N filter, i had misfiring or detonation (more likely det) at higher rev range with the turbo being boosted to 9psi. it was fine at 7 but hated 9. So I changed all the spark plugs and that helped alot, also. I heard that you need to gap your spark plugs to .6 or something like that to increase the spark for higher boost. im going to try that next along with a splitfire coil pack system from the group buys here next week.

mind u today I have got my 3 inch dump pipe, hi flow cat and screamer pipe fitted, that might increase my back firing ill have to see when it happens, it back fires randomly at the moment after around 10 mins of drivin around when the exhaust gets hotter.

Edited by Pauly33GTS-t
Link to comment
https://www.sau.com.au/forums/topic/150367-r33-revs/#findComment-2809861
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I ordered a GSP Front R/H Axle from here - https://justjap.com/products/gsp-premium-front-driveshaft-r-h-nissan-r32-r33-r34-skyline-gtr-stagea-4wd#description It lasted around a year before one of the boots blew out. I'm lowered, but I have GKTech roll center adjusters. One year seems a little premature. I think I'm going to spend the extra money on an OEM cv axle this time. This website - https://tfaspeed.com/collections/nissan-stagea-wgnc34-x-four-parts/products/nissan-stagea-awc34-260rs-rb26-right-front-axle-drive-assembly Makes it sound like the readily available OEM CV axle will only fit 11.1999 Stagea and up (mine is a 2.1997 S1). The JustJap listing didn't mention any years or anything for the GSP axle. Amayama shows '11.1999' and up as well for that part number. As well as 'plastic boot type'. See attached picture. So I guess my question is, does that axle (39100-23U60) really only fit S2 Stagea? It's the front driver side. If it does, I'd love to buy that instead of rolling the dice on another GSP. I've found that OEM one cheaper here: https://www.partsfornissans.com/oem-parts/nismo-jdm-r32-r33-r34-skyline-gtr-r32-gts4-right-front-axle-3910023u60 and here https://www.nissanparts.cc/oem-parts/nismo-shaft-ft-drive-3910023u60 Just a little confused because the JapSpeed listing for the GSP front driver axle doesn't mention any specific years or anything and it fit my S1 Stagea fine. So will 39100-23U60 fit my S1 Stagea even though technically it says '11.1999' and up? What would have changed? Thanks.  
    • Thanks for the info. The only "Issue" I've had with the shifter is I always found the throw between 4th and 6th gear too close. I'm always worried to shift into 4th accidently and sending my motor to the moon. Adam LZ recently came out with a video and stated Serialnine revised their shifters to correct this and will change all the revised parts for 150$. Strangely enough, I contacted Serialnine right after and they denied it and said it's bullshit. I found that strange as he's a distributer. I'll keep this forum post updated on that saga.
    • Yep that is correct. It allows you to adjust the short throw range from what I can tell
    • Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
    • 75% complete. Will now need to get a new axle with 5x114.3 hubs and then figure out how to customize some mudguards for it once the wheels are on.
×
×
  • Create New...