Jump to content
SAU Community

Recommended Posts

Hi guys, just thought i would post up one of the most helpful tips when installing a Just Jap or Hybrid or similar FMIC. One ommision from these kits is the nipple for the boost controller which is actually just amazing. anyway...

Some poeple believe you can take a feed off something else such as the blow off valve or something after the throttle body. this is not correct. GFB state this in bold in their Atomic boost controller install instructions and i have scoured other boost controller instructions and they all take a pressure feed from before the throttle body.

so to have this available i have used the pipe work that you would normally take out for this intercooler upgrade.

there are two stock pipes that run down throught the metal work of the car to the stock intercooler location. one you would norammly keep which runs from the turbo to the intercooler. the other is normally upgraded with the chrome piping comming from the other side of the engine bay.

if you chop this discarded pipe about 2 thrids of the way down, you can use it to replace the stock pipe that is still in place. you will then have a nipple available to feed your boost controller.

i will post picks of what i have done, but i am much happier i have finnally got the pressure feed correct.

peace out people...

any questions just ask...

Link to comment
https://www.sau.com.au/forums/topic/152593-r33-fmic-installation-tips/
Share on other sites

i just drill a hole in the pipe and tap a thread and screw in a nipple easy simple and quick

Hey mate,

Where do i go and what od i ask for to get everything i need to do this?

Also does it have any problmes leaking boost at high levels?

Cheers

  • 8 months later...
  • 2 weeks later...

What the wall thickness of the stock pipes? I dont think the JJ kits Aluminium piping is very thick. It would be nice to have about 2mm of wall thickness to tap into. You can do the pipe just coming out of the turbo (stock pipe) or the one oafter the intercooler.

If you have a pressure drop across your cooler you may get different boost levels depending where you position it.

  • 4 months later...
  • 3 weeks later...

im in the middle of installing my just jap front mount, and i just drilled a hole, made sum threads and screwed in a nipple - easy.

one problem i am having is the front indicator/parking lights dont go all the way bak into there position because the bak hits the front mount. :|

oh and the little pipe that you have to drill and connect the boost hose too looks abit wonked and its pissing me off abit, doesnt look all straight

any help guys?

ps i havent trimmed the fan blades

  • 2 months later...
  • 1 month later...
AVC-R states after the throttle???

Dudes,

A boost GAUGE would be connected after the throttle body. IE, the inlet manifold.

A boost CONTROLLER/wastegate would be connected before the throttle body.

A controller needs to open the wastegate to adjust the boost, so when you take your foot off the throttle, the pressure before the throttle body, will rise, because the throttle body will close and the turbo will still be pumping boost. So at this point the pressure after the throttle body will be bugger all (which is what you want your bosst gauge to read), but the boost before the throttle body will keep going up until the wastegate is opened. So you want your boost controller connected before the throttle body so that when the boost tries to go past what you have dialed into the settings, it will open the wastegate for you to prevent overboosting.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The average previous owner for these cars were basically S-chassis owners in the US. Teenagers or teenager-adjacent. I often tell people that neglect is easier to fix than something that was actively "repaired" by previous owners.
    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
×
×
  • Create New...