Jump to content
SAU Community

Recommended Posts

Anyone know how to take out the front and back speakers in an skyline r33 1997 model or where i can get a guide from? For the front speakers do you just pop out the grill or the whole door frame needs to come off? cheers !

Edited by sumguy
I tried to take off the passenger side door but i couldnt get the part off where off where the powerwindow button - that whole handle, it was just stuck :D

It's a barstard isn't it. There's a white latch on the underside which you hold and pull at the same time.. if and when you get it off, silicone it straight away so it's easier next time.

Where the handle is on the passanger door the actual handle that you pull to open the door from the inside has a plastic cover which unclips and there should be a screw behind it, its a bit hard to explain but thats your issue (i think) cos the same thing happened to me, you just forget sometimes where the little bastards are.

Yer, the pocket in that console... it has a round hidey-bit, with a little screwdrivery slit in it. Screwdriver the cover off, and unscrew the screw.

Then, the whole panel will come out.. it is just clipped in after you remove the screw.

Then unplug the power window switch console, or just unscrew the console out of that plastic part.

Window handle on the inside is hard to take off, but if you ease it to the left, it'll eventually unclip. From there, tug the bottom of the door, work your way towards the top. The doorskin is clipped into the door (after you remove the THREE screws at the bottom).

Then when the whole thing is loose from the bottom, lift up slightly to unhook it from the window-sill.

Pods are 4 screws. Easy out.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
    • Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
×
×
  • Create New...