Jump to content
SAU Community

Recommended Posts

yeah coating for sure. wrapping is ok, but you can get moisture trapped between the wrap and the pipe which is not good. also when you put it on, if you dont wear gloves, and then take a slash afterwards your nuts will be itchy for a fair while. this alone is reason enough to spend the dough on the coating (or wear gloves...lol) and yes I speak from experience on this.

lol.. Worse than deep heat on (or near) the nuts? :ninja:

What is the cost difference? and where would you get the ceramic coating done?

i bought those just jap dumps,and well wish i had bought better ones that bolt on...these things have the wrong size o2 sensor holes and even the reducers out of the stock 32gtr dumps dont fit?

does 33/34 gtr o2 sensors bigger and just maybe they sent me the wrong ones.. ill be ringing tomoz 2 see...

Not trying to be to much of a tight arse here but i do all the work to my own car and considering the stock 34 dumps aren't that bad and it is a pain in the arse to remove/fit new ones, would the stock dumps be fine with the right exhaust up to about the 300 r(a)wkw mark???

We fit trust dumps over the weekend to my 32 gtr.

alot of modification of the front pipe had to be done. cut down and re welded as they wernt quiet right. we also modified the rear of the trust front pipe section to 3.5 inch instead of the 3 inch flange it had on it.

Other than that i am very happy with them. bit of a f**k around. i also bought mine second hand. And had a whole exhaust shop to play in while installing them so things wernt that bad!

i think i will go back and weld on some support bars tho. we didnt quiet get around to this.

Edited by Angus Smart
Not trying to be to much of a tight arse here but i do all the work to my own car and considering the stock 34 dumps aren't that bad and it is a pain in the arse to remove/fit new ones, would the stock dumps be fine with the right exhaust up to about the 300 r(a)wkw mark???

i'd say yes! depending on what turbos i guess.

Andrew, your‘s weren't the 32 ones though were they? I thought from memory you bought some second hand that were for a 33 or 34.

and yeah, I think for 300kw the R34 dumps will be "ok" but of course some aftermarket ones would be better, but it wont be a major problem.

Andrew, your‘s weren't the 32 ones though were they? I thought from memory you bought some second hand that were for a 33 or 34.

and yeah, I think for 300kw the R34 dumps will be "ok" but of course some aftermarket ones would be better, but it wont be a major problem.

yeah i dont think mine were for 32. but we cut up the front pipe anyway at the weld just on the merge of both, so they were a little modified. mine dont have flex pipe either. and finally my exhaust doesn't scrape!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
    • Nah, that is hella wrong. If I do a simple linear between 150°C (0.407v) and 50°C (2.98v) I get the formula Temperature = -38.8651*voltage + 165.8181 It is perfectly correct at 50 and 150, but it is as much as 20° out in the region of 110°C, because the actual data is significantly non-linear there. It is no more than 4° out down at the lowest temperatures, but is is seriously shit almost everywhere. I cannot believe that the instruction is to do a 2 point linear fit. I would say the method I used previously would have to be better.
    • When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
×
×
  • Create New...