Jump to content
SAU Community

Recommended Posts

Hi guys,

I'll be swapping to an rb25 gear box shortly and i am considering a one piece tail shaft seeing as i will need to get a custom front half done anyway.

I know all about drive shaft angles and such, but as far as i can see the stock 2 piece shaft looks to run pretty straight. I suppose the other concern is the 200k old centre bearing carrier deflecting under load as my rb25 is putting out 280odd rwkw with lots of midrange pull.

Is there any feedback on one piece shafts in gtst's, i have found giant's comments on the one piece carbon vs 2 piece stocker in a gtr, but not much on gtst's which are a touch longer.

anyone?

cheers

Dave

Link to comment
https://www.sau.com.au/forums/topic/155612-1-piece-tailshaft-opinions/
Share on other sites

I run a 1 piece alloy one in my 32 gtst. It goes from the nismo gt pro diff to my rb25 box.

As u said its a straight line, so no need to worry about angles. No where near as bad as say commonwhores.

Mines great, weighs fark all (u can pick it up with 1 hand), and have had no problems at all with vibrations, or noise.

Anyone who knocks em hasnt had a properly balanced shaft in their car.

yeh...about 320rwkws and 280wide slicks and a 4k launch at morgan park off the grid snapped all the unis and spat it out......so yeh there is a rating normally. The hardy spicer one we got made had a rating in torque, however i cant remember it.

Who does custom ones Ally or otherwise? Anyone have a link i can checkout?

Being i'm putting mine back in the near future... and i think i have an R33 shaft which is 2 piece in mine, i could go a 1 piece easy enough.

So getting it done now wont hurt, plus lighter is certianly handy!

Last thing i need is to find another weak link :P

Yeh the new tailshaft had beefed up unis, one size under what supercars use i believe, gotta be nongreasable, solid core unis, not hollow greasable ones. But i think the actual tubes inbetween are rated also, depending on wall thickness and diameter. In our case the tubes didnt distort from the initial shock, only from hitting the ground after it was spat out.

Thanks for all the info.

It's handy to know that hardy spicer will do alloy ones as i had one done for my rx7 by them years ago and was probably going to go back there again for a quote atleast. Some of the prices i've gotten from places close to work for a regular old steel one are over double what i paid for the last one.

In our case the tubes didnt distort from the initial shock, only from hitting the ground after it was spat out.

Saftey loop goes a long way with a single piece :huh:

I remember someone had truck unis installed in their line, as they were much stronger than the upgraded items they had origionally...?

funny thing was we have two safety loops, one for each half...magically somehow both halves got past them without even touching them....weird.

Must have been light truck uni's cause you wouldnt fit any out of any prime mover...kenworth, mack and so on. Just too big.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Cheers. Skyline is back on the menu, can’t get rid of it. It’s like a child you don’t want, or herpes 
    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
×
×
  • Create New...