Jump to content
SAU Community

Recommended Posts

Yes that is a pig of a hose.

you will need a long set of needle nose pliers to get the clamp off and then spray a tiny squirt of wd40 inside and outside the hose and twist. it will come off.

getting it back on is another story...

yeah, there's no easy way out. You need tiny hands. Try and undo the clamp anyway you can.

Either a long screw driver if you can, or needle nose pliers.

I cut an 8 mm spanner in half and got my hand in (I lubed it up with soap and got it in - yes i was scared i'd never get it back out)

once you get the clamp undone enough, you can get the line out, by pulling the line itself from outside

If you're installing the hks turbo and replacing the line with a braided one, I have no idea how on earth you'll get the new line in.

The water line that runs around the back of the head is bolted to the head with a 10mm head bolt the same as the ones holding your fenders to the chassis.

Remove the heater hoses and push them up to gain access to it.

There is only one and its in the center of the head.

You can also access it by removing the valleycover and pushing the wire out of the way.

Remove the bonnet also it makes it much easier to see.

Why would you want to remove it though?

You can just cut the other water line pipe (return from the turbo) and join them with some high temp hose.

:)

Been there, done that. Not fun.

Having 2 people to remove it helps, one holds the hose and the other yanks on the metal line.

For install of braided lines atleast you can bend the rubber hose up and fit the barbed end of the braided line, then feed the other end of the line back around the back of the head.

The water line that runs around the back of the head is bolted to the head with a 10mm head bolt the same as the ones holding your fenders to the chassis.

Remove the heater hoses and push them up to gain access to it.

There is only one and its in the center of the head.

You can also access it by removing the valleycover and pushing the wire out of the way.

Remove the bonnet also it makes it much easier to see.

Why would you want to remove it though?

You can just cut the other water line pipe (return from the turbo) and join them with some high temp hose.

:)

Just hacksaw the metal pipe off, probably as close to the turbo as possible????

I guess I'm worried about metal filing getting in there and also, there would be no lip to stop the pipe coming off..(or would that not be a problem ? )

Have a go ya mug!!!

Actually to tell the truth, mine was held on with the hose clamps that you pinch together with a set of long handled pointy pliers [$10 at Crazy Joes or Micks or somesuch]. The hose was a bit stuck, so I used a long thin screwdriver to work under between the hose and the metal pipe and some WD40 and it came out easy. Don't ask me how to put it back on, I haven't got that far yet..........lol.

PS I don't have a valley cover. that probably made it easier. Actually I found the bolts that screw into the block that hold the stays on this hose harder to get off than the hose.

metal filings are not really an issue wiht that particular hose. That is just a coolant hose, so ti's just the cooling system - just water.

Ther'ell be plentny of shit in there anyways, like everytime I dropped the coolant in my daily driver (not my skyline), there's all rust, and crap that comes out.

Don't get metal in the oil lines though. Totally different story

It's not that easy mike, coz jase is getting the line replaced as part of the turbo install.

Also, I'd replace that rubber hose at the back. Someone recently, forgot who it was had the hose blow (they're' 10 years old afterall). Better do it now while the turbo is off. Imagine if it blows in 6 months time and having to do it with the turbo on!

If you cut the line, keep in mind that the cooling system is under pressure (up to 0.8bar). Without a bead around the line, the hose can possibly blow off. Imagine having the line blow off on a hot day as you're driving along the freeway. bye bye engine

I've just cut mine, about 30mm before it bends around behind the head. I went to pirtek and bought a compression gland to adapt some braided stainless teflon hose on. works great and looks good, and heat isn't an issue.

If ya want photos I can get some.

It's not that easy mike, coz jase is getting the line replaced as part of the turbo install.

that is wat i did when i replace my turbo with a HKS turbo. and the hks turbo came with a braided line. so i cut it just before the bent.

basicly the same as "Ol_Mate" did!

undo the bolt behind the head, then un hook that entire line from the back of the plenum... and yes replace that section onto the plenum, mine let go after my turbo upgrade, wasnt easy to get to with it all bolted back up.

you could just remove the solid line all together and run the braid from the back of the plenum

I've just cut mine, about 30mm before it bends around behind the head. I went to pirtek and bought a compression gland to adapt some braided stainless teflon hose on. works great and looks good, and heat isn't an issue.

If ya want photos I can get some.

Photos would be great !

So you didn;t need a lip on the end of the pipe with that gland thing?

undo the bolt behind the head, then un hook that entire line from the back of the plenum... and yes replace that section onto the plenum, mine let go after my turbo upgrade, wasnt easy to get to with it all bolted back up.

you could just remove the solid line all together and run the braid from the back of the plenum

Exactly what I did, you dont wanna be ripping that son of a ***** off more than once in your lifetime :( My knuckles have never been the same since :happy: /emo.

Exactly what I did, you dont wanna be ripping that son of a ***** off more than once in your lifetime :( My knuckles have never been the same since :happy: /emo.

Do it right, do it once :happy:

You can do it. Motivational thread for jase. go jase go jase go jase :)

Edited by MANWHORE

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, I can recommend the partial AV system translation CD I ordered from Car Audio Workshop in NZ. Whilst it didn't address the date issue, it has conveniently translated on-screen menu items into English, and now allows the GPS-received time to be offset in hours rather than minutes, so I can display Eastern Australian time accurately ( and bump it by another hour when daylight savings starts ).
    • Yuh, if it's 45°C outside, my car is driving in it.
    • I'd be curious to hear more. Otherwise, have you driven a modern x-trail? I wonder how it compares. Here in Australia they are/were popular for rentals and fleet vehicles. I have been in some and my impression was they are bad. But, this may have been very different in the 2000s at a good trim level. Twenty years is plenty of time to make the model worse. I do very much agree with the 2 silver cars in the garage approach. But, not driving because it's too hot would not leave a lot of time in the year for many Australians. I don't think you need to worry too much unless the car has actual issues with overheating. 
    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four-speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to its full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so stupid hot in there, that made it all the more easy -after I was standing there looking at the car and said 'f**k it'- to finally remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
    • Thanks for that, hadn’t used my brain enough to think about that. 
×
×
  • Create New...