Jump to content
SAU Community

How The &^%$ Do I Get This Water Line Off !

Birnie

By Birnie,
in Engines & Forced Induction

 Share

Recommended Posts

CEF11E Veteran

CEF11E

Posted
Posted

Yes that is a pig of a hose.

you will need a long set of needle nose pliers to get the clamp off and then spray a tiny squirt of wd40 inside and outside the hose and twist. it will come off.

getting it back on is another story...

MANWHORE Grand Master

MANWHORE

Posted
Posted

yeah, there's no easy way out. You need tiny hands. Try and undo the clamp anyway you can.

Either a long screw driver if you can, or needle nose pliers.

I cut an 8 mm spanner in half and got my hand in (I lubed it up with soap and got it in - yes i was scared i'd never get it back out)

once you get the clamp undone enough, you can get the line out, by pulling the line itself from outside

If you're installing the hks turbo and replacing the line with a braided one, I have no idea how on earth you'll get the new line in.

Slide Grand Master

Slide

Posted
Posted

The water line that runs around the back of the head is bolted to the head with a 10mm head bolt the same as the ones holding your fenders to the chassis.

Remove the heater hoses and push them up to gain access to it.

There is only one and its in the center of the head.

You can also access it by removing the valleycover and pushing the wire out of the way.

Remove the bonnet also it makes it much easier to see.

Why would you want to remove it though?

You can just cut the other water line pipe (return from the turbo) and join them with some high temp hose.

:)

BHDave Grand Master

BHDave

Posted
Posted

Been there, done that. Not fun.

Having 2 people to remove it helps, one holds the hose and the other yanks on the metal line.

For install of braided lines atleast you can bend the rubber hose up and fit the barbed end of the braided line, then feed the other end of the line back around the back of the head.

Birnie Veteran

Birnie

Posted
  • Author
Posted
The water line that runs around the back of the head is bolted to the head with a 10mm head bolt the same as the ones holding your fenders to the chassis.

Remove the heater hoses and push them up to gain access to it.

There is only one and its in the center of the head.

You can also access it by removing the valleycover and pushing the wire out of the way.

Remove the bonnet also it makes it much easier to see.

Why would you want to remove it though?

You can just cut the other water line pipe (return from the turbo) and join them with some high temp hose.

:)

Just hacksaw the metal pipe off, probably as close to the turbo as possible????

I guess I'm worried about metal filing getting in there and also, there would be no lip to stop the pipe coming off..(or would that not be a problem ? )

tridentt150v Grand Master

tridentt150v

Posted
Posted

Have a go ya mug!!!

Actually to tell the truth, mine was held on with the hose clamps that you pinch together with a set of long handled pointy pliers [$10 at Crazy Joes or Micks or somesuch]. The hose was a bit stuck, so I used a long thin screwdriver to work under between the hose and the metal pipe and some WD40 and it came out easy. Don't ask me how to put it back on, I haven't got that far yet..........lol.

PS I don't have a valley cover. that probably made it easier. Actually I found the bolts that screw into the block that hold the stays on this hose harder to get off than the hose.

MANWHORE Grand Master

MANWHORE

Posted
Posted

metal filings are not really an issue wiht that particular hose. That is just a coolant hose, so ti's just the cooling system - just water.

Ther'ell be plentny of shit in there anyways, like everytime I dropped the coolant in my daily driver (not my skyline), there's all rust, and crap that comes out.

Don't get metal in the oil lines though. Totally different story

MANWHORE Grand Master

MANWHORE

Posted
Posted

It's not that easy mike, coz jase is getting the line replaced as part of the turbo install.

Also, I'd replace that rubber hose at the back. Someone recently, forgot who it was had the hose blow (they're' 10 years old afterall). Better do it now while the turbo is off. Imagine if it blows in 6 months time and having to do it with the turbo on!

If you cut the line, keep in mind that the cooling system is under pressure (up to 0.8bar). Without a bead around the line, the hose can possibly blow off. Imagine having the line blow off on a hot day as you're driving along the freeway. bye bye engine

Ol_Mate Community Regular

Ol_Mate

Posted
Posted

I've just cut mine, about 30mm before it bends around behind the head. I went to pirtek and bought a compression gland to adapt some braided stainless teflon hose on. works great and looks good, and heat isn't an issue.

If ya want photos I can get some.

Kaido_RR Grand Master

Kaido_RR

Posted
Posted
It's not that easy mike, coz jase is getting the line replaced as part of the turbo install.

that is wat i did when i replace my turbo with a HKS turbo. and the hks turbo came with a braided line. so i cut it just before the bent.

basicly the same as "Ol_Mate" did!

Craved Grand Master

Craved

Posted
Posted

undo the bolt behind the head, then un hook that entire line from the back of the plenum... and yes replace that section onto the plenum, mine let go after my turbo upgrade, wasnt easy to get to with it all bolted back up.

you could just remove the solid line all together and run the braid from the back of the plenum

Birnie Veteran

Birnie

Posted
  • Author
Posted
I've just cut mine, about 30mm before it bends around behind the head. I went to pirtek and bought a compression gland to adapt some braided stainless teflon hose on. works great and looks good, and heat isn't an issue.

If ya want photos I can get some.

Photos would be great !

So you didn;t need a lip on the end of the pipe with that gland thing?

`nigno Rising Star

`nigno

Posted
Posted
undo the bolt behind the head, then un hook that entire line from the back of the plenum... and yes replace that section onto the plenum, mine let go after my turbo upgrade, wasnt easy to get to with it all bolted back up.

you could just remove the solid line all together and run the braid from the back of the plenum

Exactly what I did, you dont wanna be ripping that son of a ***** off more than once in your lifetime :( My knuckles have never been the same since :happy: /emo.

MANWHORE Grand Master

MANWHORE

Posted
Posted (edited)
Exactly what I did, you dont wanna be ripping that son of a ***** off more than once in your lifetime :( My knuckles have never been the same since :happy: /emo.

Do it right, do it once :happy:

You can do it. Motivational thread for jase. go jase go jase go jase :)

Edited by MANWHORE

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      M35 Aftermarket Fuel Pump

      By MBS206 · Posted

      Pressure when IDLING, is meant to be 51PSi... So that amperage value needs to go up a fair chunk... I'd personally be factoring for more like 12amp at least on those runs, and at that point you need to hope the already there wiring doesn't drop you a volt or two, as that's a lot of fuel pressure flow drop off from 13.5 to 12V! Taking idle pressure of 51psi, means the pump will be drawing a MINIMUM of 9amps all the time based on your reading of the graph (3bar base, then allowing an extra 0.5bar for boost = roughly 51psi)
    • Ben_D
      Wanted to buy R200 longnose LSD 3.9 ratio

      By Ben_D · Posted

      Hi all,  I am in the market for an R200 longnose diff out of a Z31 300ZX, or S12 RSX, DR30 skyline, or similar, in a 3.9 ratio.  Preferably a late model one with the M12 crownwheel bolts.  The only easy to find advert for one of these was my ad back in 2007 when I sold it on this forum.  I sold the diff as I had sold the car it goes to, but as it turns out, after 18 years I got the car back late last year, so now I'm looking for the diff !  If anyone knows where to find a longnose R200 LSD with the M12 crownwheel bolts, drop me a line at [email protected] - Bonus paid if soomeone comes up with the original diff (stranger things have happened !).  Cheers   Ben D    
    • Ben_D
      Back for more after 18 years - and where are the longnose R200 LSDs?

      By Ben_D · Posted

      Hi everyone, I used to post here a bit from 2004-2013, when I owned various Nissans, in particular my S12 RSX gazelle, which was sold in 2007.  As luck would have it, after an 18 year hiatus, the car found its way back to me last year, and over the past 11 months I have had the pleasure of restoring it with my kids.  One thing that I am after in particular is a 3.9 ratio R200 LSD for it.  I actually sold the one out of the car here back in 2007 , and it would be incredible if I could track down who I sold it to, so I can see how they have progressed over the years (and to be honest, to see whether I can get the diff back !).  Anyways, hi all and let me know "where are the R200 Longnose diffs all at these days ?  Cheers Ben D  
    • sonicii
      G35 Control arm and Compression Rods into a V35 Skyline.

      By sonicii · Posted

      Arms will be the same as the G35 or 350Z, but as above, there was a change in the lower control arm where it connects to the ball joint.  That said, you can remove the ball joint cone from your old ball joints and fit them to the new ball joints.  To be honest, I didn't think the ball joints themselves were different. The main ball joint is a bit awkward to replace, you really need to remove the steering knuckle to press out the old one.  Some people have used tools to remove it in place, but it just seemed too hard to get to. If you are going to press out/in that ball joint, then you may as well just replace the bushings in the LCA and the compression rod.  You can buy the compression rod bushing from Nissan, but the LCA bushes, you will need to go aftermarket. Much cheaper than buying the whole arm.
    • Erelyes
      Ceramic turbine damage to engine - what did yours do?

      By Erelyes · Posted

      Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
×
×
  • Create New...