Jump to content
SAU Community

Recommended Posts

UPDATE: Read last post by me plase. I really would appriciate some input on this. Driving me nuts.

It has got to the stage where the car, just coughs it's guts up in the morning and then coughs some more, untill bang 1200 rpm.

________________________________________________________________________________

________

This is exactly what is happening to my car

"Hey just a small annoyance with my cold start. When starting the car up for the first time on the day the idle goes to like 600,700rpm kinda stumbles then just revs out kind of wakes up and then just warms up normally and yeah everything else is fine i know kind of picky but yeah just abit annoying. For the rest of the day turn the car on when cold warms up normal but if its not driven for more than a day or two then yeah does it again could be the cold but also wondering if it may be related to the tps??"

My car also seams like it only fires up 3-4 cylinders, then clears its throuat and fires up all 6.

The compresion test is ok 150 across all cylinders.

Does anyone know the anwser to this.

Post taken from

http://www.skylinesaustralia.com/forums/in...=124145&hl=

Edited by WogsRus

I used to have issues with idling even when warm.

Commuting after an hour and at the lights and it would just drop and stall...or go up to 1200.

Now have Power FC and hasn't happenned since. Dunno why.

Also, there is an ACC (or AAC) valve cleaning thread in the DIY section. That controls your idle. Doesn't look like too much work so maybe give that a go

nope car uses no Water ot oil, has no blow by or anythign of that nature. Itseams to have started to happen after I started to modify the car. I am running a Centra 20 ECU, which does not have the little idle adjustment screw on it, so i am not sure at all.

There is no wate rin the oil or vice versa. Engine compression is 150psi across teh board, and all seams ok. I wander if it sould be a leakying injector or something?

What's a: Centra 20 ECU?

Is it compatible with the s2 engine?

Has the cold start been tuned properly?

Have you tried refitting you std ecu in?

This sentance makes no sense, please clarify: "There is no wate rin the oil or vice versa"

Could also be a leaky injector, but i'll check my mods first, as it only started once you started to mod it.

Central 20 is a tuning house in Japan. Its a remaped Ecu from them

The cold start is preset. It is not tunable in Australia, as Dr DRift has not got the hardware to do so yet.

There is no water in the engine oil or vice versa. So radiator and sump are both clean, no problems there.

It did the same with a standard ecu. The ecu does not have an autolearn function, like a PFC, it's preset to a set map and that's it.

Reseting has not done anythign at all.

I have replaced the watter coolant temperature sensor already, as the old one was bugared, this one has done abut 6 months work.

The thing is, it only does it first start in the morning. If i start the car any time after that, it is ok, no probs there.

When stock, the car had no issues, it's only after i started to mod the car, that this has begun to occur.

It did the same this morning, it kicked over on 4 cylinders or so, then coughed and fired up into life

OK GUYS SO HERE IT IS AND STILL NO GOOD.

I maybe thorght a head gasket, but ie:

http://www.skylinesaustralia.com/forums/in...id=2943614&

But nope all fine.

SO what i did is this.

OK well so this morning, after running the car empty of fuel last night in the fuel rail (pump off car cranking and fired up) and the cap of the radiator to stop any pressure into the block.

THE Car still started like crap. DAM IT. i dind't get a chance to clean the AAC, but that seams to work ok, once the stumble has disapeared.

I primed the lines, waited for the pump to go off, and blupp, blup blup, cough, cough, vroom 1200rpm. ONLY WHEN COLD IN THE MORNING DAM IT.

I have almost rulled out the head gasket, as it never uses water, not a drop, no bubbles ect.

So i checked the plugs and this is what they looked like, ALL THE SAME, i also put some REDLINE FUEL CLEANER SI-1 as i have had so many good reviews about it, but have only done 50km sinse that was done, so see how it goes.

SO WHAT THE HELL IS IT.

What is the best test for vacume leaks, i have sprayed arround with carb cleaner, nothing.

What i was thinking, is getting my smoke machine, yess i have one, putting the smoke in the cooler piping, through the turbo, basicaly where the AFM is, and pressurising teh system to 15 psi with an air comressor, that way the smoke will give me an indication of any leaks.

I am loosing so much fcucking sleap over this car, i just want it to run right. COME ON.

HELP ME before i sell it.

PS. For images of sparks please read above thread.

Mate living in Tas means anything to do with an import, will cost 10 times more then a Falcodore.

It sux, hence why i do it all myself.

Also being a mech engineer (who can't spell), i figure i can do it

I don't trust any mechanics with any of my cars. Esspecially here in tas.

Nissan here are usless, stuffed up so many cars, no one goes there for servicing. Consult comes back with nothing.

Oh well any more ideas????

outside of rail, you mean remove them and get sonic cleaning?

If so, then nope, not yet, but about 15k ago they were pulled out and found to be fine. But like i said, i drained the whole system of fuel, and then let sit over night. So there was no fuel in the injectors. Then after repriming the lines, it still did it.

Stock ECU no differance, did the same.

No i have not tried and AFM as yet, it has been cleaned, but still teh original item. How does the AFM contribute to this issue only when cold, and fine all the other times?

Thanks guys keep them comming.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...