Jump to content
SAU Community

Recommended Posts

Last friday I installed a Gates Racing timing belt, new idler& tensioner pulleys (and idler pulley bolt), aswel as a new Tomei adjustable exhaust cam gear (now set at 4degrees retarded).

Had the car re-tuned today to suit the new adjustment. Last dyno run made 248kw

now makes 260kw :D im stoked with the result! power comes on earlier, smother, and with a touch less boost (17 psi rather than 18). All my runs are on BP ultimate 98 octain fuel.

theres a few pics below of the belt, cam gear & dyno sheet.

for those who dont know...the cars basics: Stock engine

pod filter

FMIC

AVO hi-flow turbo

big injectors

big fuel pump

adj fuel reg

tuneable ecu

turbo back 80mm zaust & hiflow cat

post-7879-1172573321.jpg

post-7879-1172573826.jpg

post-7879-1172573954.jpg

Link to comment
https://www.sau.com.au/forums/topic/158351-new-dyno-results/
Share on other sites

do you find it a big boggy now that youve taken off the factory VTC solenoid ?

VTC is still there (just not in the photo). Its more resposive than its ever been now

Just a few questions:

1) Did u consider adding an injector instead of getting 6 bigger ones? Is so y did u choose to go bigger

2) How much more can ur highflow turbo do?

3) At what point do u reckon ull start to need to do internals?

1) No. Maxed out my stock ones at 220kw...so got bigger. Only $20 difference btw 550 & 840 so I just chose the bigger because I know there a pain to change an now i'll never have to do it again :(

2) the turbo can be pushed to about 22psi safely....but my head gasket can cope with that as its still stock.

3) most people say at about 280-300kw is where you should be looking into forged pistons (even though the stock ones are forged) and better rods (most people use linished GTR rod)

So by retarding the exhaust cam 4degrees, you gained 20kw atw?

Nice work.

aswel as re-tuning the car to suit :)

Yeah, I was over the moon! my tuner cant believe the power my car makes with stock engine an small turbo. Its averaging around 12.5 A/F ratio under load too which is still a safe tune. could get more if i leaned it off an ran more boost....but i dont want to. Maybe for a few runs on the Dyno at Autosalon to impress...hehe

thanks mate!

No real plans for further power. more power = bigger turbo & engine bottomend rebuild to cope = expensive

just hunting down some nice rims now an thats about it

just having fun with it this year, few deca days track day & drift training days....

by tunable i mean aftermarket. I run a microtech LTS-12 :(

looks like now with that little extra power im in need of a catch can....few reports of seeing blue smoke from my car after full throttle acceleration then backing off....its creating a bit too much pressure an the oils getting by, so catch can will rectify this.

thanks to those for letting me know

looks like now with that little extra power im in need of a catch can....few reports of seeing blue smoke from my car after full throttle acceleration then backing off....its creating a bit too much pressure an the oils getting by, so catch can will rectify this.

thanks to those for letting me know

Yeah I was tellin Kris about that...I was behind you and was coppin a fair amount of blue smoke...thought somethin might have been wrong...then a few times right after the blue smoke would be a pretty thick puff of thick white smoke...

nice result mate....got mine sitting there and was going to to the belt soon...

I saw the blue smoke when u backked off...was going to pm u about it but forgot...

nice result...I hope I get some similar gains...will try with a de-cat setup just for the dyno to see the difference between my hi-flo cat and nothing...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yea my thought was tighter engine when hot is more load a poor ground connection can't take. On that note, I had time to check my driveshaft verical alignment tonight, it's +2 and -2 at either end, so thats perfect and how I had set it up last year. What would be the easiest way to check horizontal alignment between my diff and transmission? I can think of a few ways but they're all complicated and I feel like I'm overthinking it. I'm hoping it's that as I can't see any other reason why I have developed driveline vibration since I put the motor back in. 
    • Thank god. I thought I was the only one, nobody seems to mention this (cause nobody really goes this far in Sedan land). The car's track is 10mm wider at the rear, which explains why the rears sit a little further out for the same size wheels. There's not really many options in widebody land for sedans anyway - People will just use whatever came out of the box and then buy wheels/spacers to suit. To get it perfect you'll likely need custom wheels with custom offsets if you really want to get it perfect which is what I plan to do, but I also plan to utilize more of the inboard space for tyres at the rear... which is also something nobody ever seems to do.... OR my maths have failed me after 20,000 attempts and I'm about to make huge mistakes. 
    • What colour is that?  A mate of mine went red/black on his SLR5000 tribute recently also.  And yes, also glad to see this still progressing albeit slowly. 
    • found a company that makes a flat gauge face 3-d printed mounting base kit to eliminate the dished style gauges. if anyone else is looking to do the same https://www.dashfreaks.de/shop/flat-dials-holder-nissan-skyline-r34-gt-gtt/    
    • I installed my link ecu shortly after. But car ran fine with stock ecu and r35 coils, just had the traction control and slip lights on.
×
×
  • Create New...