Jump to content
SAU Community

Engine Mount Fabrication - Lots Of Pics.

bubs

By bubs,
in Fabrication

 Share

Recommended Posts

bubs Apprentice

bubs

Posted
Posted

Just thought some might like to see the gearbox mount and engine mounts I made for a RB20DET in to a BMW E36.

For more detail on the swap go here. http://www.eurocca.net/forums/showthread.php?t=17736

Gearbox mount

BMWRB20_0001.jpg

Gearbox crossmember is a single piece of 8mm plate with a section piece of 40x40x4 RHS on top.

BMWRB20_0003.jpg

Here it is installed.

Engine mounts

BMWRB20_0006.jpg

Here are the piece which are to be welded to the original BMW crossmember, these are cut with a 4 inch grinder from 4mm plate.

BMWRB20_0007.jpg

Tacked together

BMWRB20_0008.jpg

Here are the welded left and right profiles

BMWRB20_0010.jpg

welded to original crossmember

BMWRB20_0011.jpg

Close up of welding

BMWRB20_0014.jpg

Reinstalled in car with Nissan Patrol engine mount in place

BMWRB20_0018.jpg

Notice plate on engine mount rubber and plate bolted to the block.

BMWRB20_0019.jpg

Started by making a plate to join the two and tacked together.

BMWRB20_0020.jpg

Once I had it tacked I pulled it out and boxed it in.

BMWRB20_0021.jpg

Welded out ready for paint.

BMWRB20_0022.jpg

Reinstalled.

BMWRB20_0023.jpg

Now repeat.

BMWRB20_0024.jpg

Job finished

  • 3 months later...
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      ECU sees many times the speed than speedo does (R34 swap)

      By Kapr · Posted

      Hi. This is just my curiosity because iam sure the tuner figure something out...but either way i want to ask. The "problem" is that the Nistune ECU (Stagea FW and RB25DET NEO from Stagea) sees many times the speed than the speedo does(he says the speedo show 120 km/h - correct speed and the ECU shows like 510km/h ) I told him that this car/tranny getting speed from rear diff. If iam not mistaken the RB25DET NEO "need" to see tranny speed sensor? (my tranny has the plug for it). So couple of "question" If he connects/wire the speed sensor to the tranny...are the signals gonna intervene and if...what if he disconnects the rear diff one and the speedo stops working? Or the "new" sensor from the tranny "take over" and will not going need the one from diff? As i said i know he figure/get that done...iam just curious to know what are the solutions 🙂 
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      Your IACV is set to idle too low. You need to adjust it via the screw Duncan mentioned. From memory it should be 650rpm with the valve electrics unplugged. What is it trying to idle at with the IACV plugged in?
    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Ahhh, I need the whole head unit. I definitely needed to roll back through and review your setup, ha ha! Neat setup they have going on. I just need a full double din head unit. But I want good and responsive. I might have to review what the likes of pioneer have out these days.
    • albyz34gt
      34 de+t conversion using s2 stagea automatic transmission, engine harness and ecu

      By albyz34gt · Posted

      Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Duncan
      R32 GTS (RB20DE) Injectors Replacement

      By Duncan · Posted

      Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
×
×
  • Create New...