Jump to content
SAU Community

Recommended Posts

mate just brough an xr6t and while probably quicker, it doesnt feel as violent when shifting through gears (and comming on boost). so it had quiet a smooth power delivery compared to my line. only having around 170rwkws mine certianly feels like its going harder but im sure it aint.. ;)

Edited by jake33
Link to comment
https://www.sau.com.au/forums/topic/159201-r33-vs-xr6t/#findComment-2954915
Share on other sites

IIRC the XR6T has a 14.1 sec stock quarter mile time and the R33 has a 14.4.

But then you have to realize that your comparing an 18k car to a 35k car. Likewise the XR6T is newer, and should have alot better tech crammed into it and less K's on the clock. 4L vs 2.5L. Large curb weight vs medium curb weight. 4 door vs 2 door. Auto vs manual.

At the end of the day, its still a Ford and thats why it loses.

(at least in my opinion)

FYI, http://www.skylinesaustralia.com/forums/in...showtopic=80479

Link to comment
https://www.sau.com.au/forums/topic/159201-r33-vs-xr6t/#findComment-2955319
Share on other sites

zoom did a tech article on the xr6t. they took the centre muffler out and gained 17kw, and it was still well under the legal sound rating.

stock for stock i'd say the xr6t would beat a gts-t or gtt skyline. and if you start modding them to a point where you start changing ecu's then the xr6t will hose a gts-t/gtt. just by remapping the stock xr6t ecu they can gain up to 100hp (remember that these cars were detuned to have less power than the v8's. there were a few cars recalled because they had a 300kw tune in the ecu - which is what ford was orginally going to run them at). there is one in town tat has just had exhaust, flash tune and boosted up to about 11psi and it put down 390hp (290kw). there are also guys with reasonably stock typhoons getting high 11's. they just do airbox and exhaust mods.

Link to comment
https://www.sau.com.au/forums/topic/159201-r33-vs-xr6t/#findComment-2956423
Share on other sites

my sister-in-law's boyfriend has a xr6t. i was sitting at the end of the street in the rain 1 day and he came off the roundabout and up the hill. he didn't floor it but gave it a little bit of gas and the traction control kicked in for a second. that sounds cool. its like having a rev limiter kick in when the exhaust note is at its deepest. was the best sounding limiter type noise i have heard, cause it wasn't screaming, it was nice and throaty.

Link to comment
https://www.sau.com.au/forums/topic/159201-r33-vs-xr6t/#findComment-2956599
Share on other sites

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
×
×
  • Create New...