Jump to content
SAU Community

Recommended Posts

usually takes a fair whack of power to turn the starter.

sometimes if you get a flat battery that is drained enough, it doesn't even have enough power to throw out the solenoid in the starter to engage it... (the clicking noise with a 'normal' flat battery)

we get it all the time at work (i work in roadside assistance) where people say "but all the lights on the dash/headlights/etc are working, the engine just won't crank" - 99.99% of the time it is a flat battery.

Link to comment
https://www.sau.com.au/forums/topic/159939-car-wont-start/#findComment-2970011
Share on other sites

usually takes a fair whack of power to turn the starter.

sometimes if you get a flat battery that is drained enough, it doesn't even have enough power to throw out the solenoid in the starter to engage it... (the clicking noise with a 'normal' flat battery)

we get it all the time at work (i work in roadside assistance) where people say "but all the lights on the dash/headlights/etc are working, the engine just won't crank" - 99.99% of the time it is a flat battery.

I pray your'e right. Thanks for the reply bro.

Link to comment
https://www.sau.com.au/forums/topic/159939-car-wont-start/#findComment-2970050
Share on other sites

Mine was doing this (sometimes turned over and started instantly) sometimes all it did was 'click' and nothing.

Turns out mine was worn out terminal contacts at the starter motor due to low voltage cranking.

So check battery first to see if it is just an 'almost dead' battery, then move onto the starter motor, including all connections to starter and battery.

A 'relay' was added to my starter to help with the low voltage to starter (although I don't think this was the ultimate solution). I'm going to, when I get the time, replace the positive and negative cables (battery -'ve to block, etc) because I'm thinking my car has a low voltage problem altogether due to poor condition, and size, of these cables. The -'ve cable to the block and negative battery terminal itself looks greasy/dirty and is of small size.

Fixxxer :worship:

Link to comment
https://www.sau.com.au/forums/topic/159939-car-wont-start/#findComment-2971346
Share on other sites

usually an alarm won't stop it from cranking though....

what? nearly every immobiliser I know if disables the starter motor... it's usually one of the 3 points of 'cut'. fuel, spark, starter.

Link to comment
https://www.sau.com.au/forums/topic/159939-car-wont-start/#findComment-2973992
Share on other sites

If it turns out it wasnt your alarm your starter motor could be cactus. Check that its not your battery by turning on the headlights onto something, so you can see them and if they go out when you try to crank your motor then its your battery. if they stay on and only dim a little then its your starter motor...dont know much about the alarms so i hope this helps :nyaanyaa:

Link to comment
https://www.sau.com.au/forums/topic/159939-car-wont-start/#findComment-2974281
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...