Jump to content
SAU Community

Recommended Posts

Hi all just got a wierd problem I've got a power FC on my R34 now all of a sudden when i start my car it idles fine then when i turn the lights on it revs to 1500rpm then drops to 1000rpm then goes back to 1500rpm and repeats over and over then when i turn the lights off it goes back to normal. :P Anyone have any ideas my BOV is set to full plumb back im going to try putting the standard one on tomorrow and see how it goes I also think it might be the AAC valve. Anyone have any ideas???

Edited by J34
Link to comment
https://www.sau.com.au/forums/topic/160932-strange-idle-when-lights-are-on/
Share on other sites

Not sure if Pfc's have "voltage compensation", but if they do, this needs to be tuned.

Either way this sounds like a tunning issue; take the car back to your tunner and ask him to ajust the tune accordingly. It could be a 2min job.

Hi all just got a wierd problem I've got a power FC on my R34 now all of a sudden when i start my car it idles fine then when i turn the lights on it revs to 1500rpm then drops to 1000rpm then goes back to 1500rpm and repeats over and over then when i turn the lights off it goes back to normal. :pirate: Anyone have any ideas my BOV is set to full plumb back im going to try putting the standard one on tomorrow and see how it goes I also think it might be the AAC valve. Anyone have any ideas???

Re-run the 30 minute idle learning procedure - this should fix it.

As far as i know to get to the idle reset requires the tune to be wipe the whole tune which i really dont want to do. I just put my stock BOV back on and cleaned the AAC valve it now idles better than ever untill I turn the lights on then its the same problem Anyone know of any Power FC Tuners close to Northern Sydney/ Northern beaches???

Hmm, I don't know anything about the PFC or how it's wired in etc. But if it were me I'd be starting with the basics, make sure the battery terminals are clean and tight, check alternator charge rate with the head lights on and off and check all earth connections. That's how I'd approach this.

It might be your AFM.......give it a dust out...while you are at it clean your filter/

This sometimes can cause your problem.

It seems to me like a air/fuel problem...you said it just started to happen....so your tune might be fine.

My nephews car use to cut out on him...until he re-soldered and cleaned his AFM's.

Could also be your injectors...put some injector cleaner in your tank.

Good luck finding your fault.

Well I drove the car to Unique auto sports today and was fixed in about a minute. Some adjustment in the idle control on the PowerFC seemed to have fixed it up :sorcerer: So free plug for UAS! :stupid:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...