Jump to content
SAU Community

Recommended Posts

oil in the catch can is usually from the crankcase ventilation or leaking from the intake

the usual culprit is the oil seal on the turbocharger, they can die / perish

a catch can simply catches it and does nothing more

its more like a fail safe / press F8 to go into safe mode kinda device

empty it out

check your intercooler piping for oil marks and clean them away

drive around for 2 days and check all again

if you have more oil back and piping is oily (as in substantional) then it could be shagged oil seal on the turbo

thanks paul...

yeah i know what the catch can does, i'm just basically asking whether it soulds like the problem is the engine or the turbo or something else?

so you think turbo on its way out?

i might go get a compression / leak down in the next few days while i keep my eye on the turbo and catch can..

As the other guys said.............. also.... could be happening is that u cracked a piston....... usually number 5 or 6. thus letting oil into your cylinder thus causing detonation thus no good!!! The car will run fine for a while but these are a couple of signs. Get it diagnosed properly. Ask your mechanic to do a 'leak down test' this should work out what and where its happening. I know all this coz i have the same problem!!!! except mine has not only cracked it has sh%t it self!!

Yes, you have a problem with pistons / rings sealing inside the bore. I once saw a R34 GTR that would effectively empty its sump into the catch can as soon as it hit boost - turned out to be a hole in a piston.

last comp test was done 1 month ago and was all fine. have spoken to the mechanic and he is going to do another one next weekend

he seems to think it might be PCV valve bolcked or stuffed, so i took it off properly and gave it a good clean

after a few days of good hard driving i haven;t seen another drop in the catch can yet..

I may be able to shed some light on it.

you were not suffering from blow by before the cams by the sounds of it. but since they were installed and even on the dyno you were getting blow by :(

I am guessing the cams have a much longer duration. if that is the case the overlap would be greater. and it has to go somewhere :D

I have seen it once before and the problem was cured with adjustable cam gears and 3 deg retard on the exhaust and a whole 5 degrees advance in the inlet.

There cars were regrinds and i do not remember the specs.

the car was making more power after the cam gear adjustment and no more blowby :D

Hope this helps!

did the cams produce more power?

cams produced about 7rwkw more at the top end but heaps more midrange... but that was with adjustable gears as well... not just cams on their own.. i have no idea what the gears are set at though..

when my mechanic checks the compression i will get him to look at the cam gears also to see where they're at..

yeah the poncams are 256deg duration and 8.5mm lift

yeah but if there's severe blow-by caused by a piston problem, then its going to show up on a compression test.. or so i have been told

the car is not blowing any smoke, and still drives exactly as it has the last 4 years i've had it. if there was no oil in the catch can that one time you would swear there's nothing wrong...

sowwie guys not offering any advice on this matter but just wanting to know how much leak down test cost and last.. my rear turbo exhaust previously ended up in the cat and i was told to get a test done to make sure it didnt damage anything else.. cheers

catch can has been installed as is for the last 12 months and nothing has changed, so unless one pipe has become blocked for some reason, its not the plumbing...

well will see how the drivability changes

obviously i'm trying to grasp hold of any hope here (thus why i'm trying to tell myself its something not serious) and denial is a powerful thing, but i'm just going to keep a close watch on it as its still driving fine

i appreciate everyone's input

Warren.

Leak down always shows stuffed ring lands, usual comp test doesn't always. Piece of mind to stop those sleepless nights get it done. As a bonus you know the condition of the motor a little better. Maybe take it some where else just for the leak down if your current mechanic believes a regular comp test is as good as a leak down at showing engine problems.

Good luck..

Give in to the dark side............<looks at avtar> You know you want to. :laugh:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
    • I forgot about my shiny new plates!
    • Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
×
×
  • Create New...