Jump to content
SAU Community

Recommended Posts

Hi Guys,

Just wondering, it seems that when my car is idling it has a really faint miss every couple of seconds or so, nothing major and it drives fine under load and makes good power, just wondering if this is normal? It's hard to describe but its kind of like instead of having a constant purrr for the idle every 2-3 secs theres a slight quiet and then it starts purring again.

anythign to be worried about? Car is an R32 GTR.

Link to comment
https://www.sau.com.au/forums/topic/161260-slight-miss-on-idle/
Share on other sites

I guess its fairly normal. Try new plugs first see if it helps. If not then get your injectors cleaned see if that works. I've just got my injectors done and its a fair bit better. Yet to see if there are any improvements in fuel economy yet tho.

Mine has done it ever since moving away from the heat range 5 1.1mm gapped plugs.

If I open the gap up the idle smooths out.

The miss is stuff all but I guess it can be an annoyance if you expect it to be baby smooth. No such thing with a modified car. :)

Mine has done it ever since moving away from the heat range 5 1.1mm gapped plugs.

If I open the gap up the idle smooths out.

The miss is stuff all but I guess it can be an annoyance if you expect it to be baby smooth. No such thing with a modified car. >_<

I found the exact same thing going from 1.1 to .8 gapped plugs.

iv got his problem aswell and iv changed my plugs and put new spitfire ones on and no change

This can also be caused by resistor pack and wiring to the resistor pack.

Or even earthing of the resistor pack.

Most get a lot of heat over the years and need some attention.

You will know there is a problem when you operate the air-con.(at idle) and it misses regularly.

  • 1 year later...

Have we figured this out? I just changed from 5 plugs gapped to 1.0mm to 6 plugs gapped at 0.8mm and now I have this half miss stumbling sound coming from the exhaust every few seconds. Any updates?

Edited by cpt_impossible

Maybe get new coilpacks and clean the injectors like what others have said above?

I've noticed that this has started happening to my car as well. It's got splitfire coils and a change of the plugs about 3 weeks back and no change. A clean of the injectors might help, but too much a hassle. Everything is running good except for the idle so it doesn't bother me.

Yeah it happens when your spark plugs are gapped too close: from wiki

The gap adjustment can be fairly critical, and if it is maladjusted the engine may run badly, or not at all. A narrow gap may give too small and weak a spark to effectively ignite the fuel-air mixture, while a gap that is too wide might prevent a spark from firing at all. Either way, a spark which only intermittently fails to ignite the fuel-air mixture may not be noticeable directly, but will show up as a reduction in the engine's power and fuel efficiency. The main issues with spark plug gaps are:

· narrow-gap risk: spark might be too weak/small to ignite fuel;

· narrow-gap benefit: plug always fires on each cycle;

· wide-gap risk: plug might not fire, or miss at high speeds;

· wide-gap benefit: spark is strong for a clean burn.

A properly gapped plug will be wide enough to burn hot, but not so wide that it skips or misses at high speeds, causing that cylinder to drag, or the engine to begin to rattle.

I have mine gapped at 0.6 because my coilpacks are shit and i need new ones, but it fixes my hi-rpm misses, so until i save up for some splitfires i hav to put up with the missing at idle,

So yeah check the gap on your spark plugs, ideally should be 0.8

I have the same idle-popping issue.

Regarding plugs, I've read that the amount of resistance with power getting to the plug can change the ideal gap for your engine. So I guess a lengthy trial-and-error testing period is going to be the best way to get things the way you like them.

Edited by Legumis

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...