Jump to content
SAU Community

Recommended Posts

Hey, ive put an advert up on allclassifieds.com.au for this aswell but i figure, more publicity = faster sale :)

Its 110cm x 50cm x 50cm and holds 275 Litres and is being sold as a complete setup which includes:

Fishtank

Stand (120cm x 75cm x 60cm)

Gravel

Lighting (Fluorescent globes replaced october of last year)

Ornaments (as per picture below)

Filter (Fluval 304, not 100% sure on whether it still works as it has not been used since November of last year though it wouldnt cost more then $50 to repair and considering a new pump suited to this capacity tank can cost over $300) Comes with all filters, piping etc

dsc00107xa2.jpg

dsc00106ni8.jpg

The item is located in Murrumbateman (25km out of Belconnen and 20km before Yass travelling on the Barton HWY) and pickup is a must unless anyone is willing to sort out another form of transport (eg paying petrol for me to deliver it).

Asking for $350 for the complete setup

call me on 0423-126-050 if you have any questions or email me at '[email protected]'

Edited by Baconer

:) always loved having fish (this tank was full of tropicals at one point) especially neon tetras, nothing looks better then the fluoro lights reflecting off a school of 20 neon tetras. They are cheap as anything aswell, $2.50 from memory.

neon_tetra.jpg

Shame theres no where to keep it but there isnt enough room in the new house (moved from a 2 story 5 bedroom to a 3 bedroom 'cottage') so a lot of our amassed junk is being sold off.

If you get the green light from your boss just send me a pm :D

Edited by Baconer
  • 2 weeks later...
  • 3 years later...

sold! pick it up 3 years ago

Oh. I know. I'll turn him into a flea, a harmless little flea! And then, I'll put that flea in a box. And then I'll put that box inside another box, and then mail that box to myself. And when it arrives...

AH HA HA HA HA, SMASH IT WITH A HAMMER!!! IT'S BRILLIANT, BRILLIANT, BRILLIANT, I TELL YOU!!! GENIUS, I SAY!!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...