Jump to content
SAU Community

Recommended Posts

I quite like the HKS Hypermaxx II. Thye best car i have ever driven at teh track had them and Nismo adjustable arms. The car was brilliant to drive. Much better then my car.

On the street though it was a bit harsh...but on the track i quite liked it. And combined with that it seemed very quick and grippy as well

Yeah...spot on with what I would say.

My HMax2's are very noisy (compared to the standard)..but are simply awsome and provide much confidence when trying someting you 'saw in a cartoon' once!!

Mine are set to super-soft setting, but they still wreck your back!!! LOL! >_<

Regards,

Superspit.

  • Replies 69
  • Created
  • Last Reply

Top Posters In This Topic

can't take credit for finding that article - its stickied here in the suspension section. just seemed relevant to link into this thread.

http://www.skylinesaustralia.com/forums/in...howtopic=161623

, but to say its not a handling track I think is a little far fetched.

To go very fast around Sandown (I'm talking sub 1:20's), there is a lot of ripple strip jumping, a suspension with short travel and the inability to absorb bumps at speed will throw the car off the track.... I'd be inclined to say that you'd need less suspension at PI than you would at Sandown, coz of how smooth PI is.. Correct me if I'm wrong...

My car is much happier at Sandown then it is PI. I run out of suspension real quick at PI, but at Sandown the soft suspension allows me to brake deep at turn 1 with all the bumps and hammer ripple strips. LOL...at PI i lift the slightest amount and my car gets lost mid corner with no stability :) PI needs a lot more spring just becuse of the corner speeds/Gs. Sandown needs good shock/spring setup so you can handle the bumps in braking areas and ripples strips. So different thats all.

I now agree with JAGR33. Sandown my be a drag strip, bu ti think you need far better suspension as it is simply so bumpy. PI is smoother and with crappy suspension you are simply slow. With crappy suspension at Sandown...you may end up in a lot of strife if the car does not ride the bumps as me and RowdyR32 have founf out

Brisby - you could have $20K proflex suspension but if you jump on the brakes with oil on your rear tyres you're still going to crash into the wall.

Having said that Sandown does need some suspension that can ride bumps as has been said already. I'd add wakefield to that from my short experiences there. IMO the standard shocks are better at Sandown than a lot of the hard jap stuff. But the opposite is true at PI.

If I was going to have picked a suspension from the original list it would have been the Tein Flex. They seem by far the best of the "basic" Jap stuff that is available.

I dunno if anyone has mentioned it but have you had a look into these...?

http://www.silkroad-jp.com/section/a8.html

Im currently using TEINS (GTS4 - still the same) but have experienced a car using the Sections and i instantly fell inlove, deff swapping when the time comes!

I would however say that the ride was something that wouldn't be pleasant day in day out with normal driving.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...