Jump to content
SAU Community

Recommended Posts

Rang Pedders in Hornsby for a quote:

Front Castor bushes $99 -OK

Fornt lower control arm bushes $205 - hmmmm

Here's where i think it gets silly

$330 install +$75 wheel allignment

$300 install for front and rear coilovers

=$675 labour.

Is this how much it costs?

on my old car a lil maz 323 i had my shocks and stab bar rubber and eye bushes replaced for $130 at my local...

ring whiteline for another opinion on the parts costs.

install costs depend on where you take it. $60-75 for a wheel alignment is not uncommon. the amount of labour also depends widely on the specific car and its suspension, some suspension is easy to pull apart some of it you are at it for ages.

labour costs to pull all your suspension apart are always going to be higher than a couple of little bushes.

Prices like that mean they don't really want the install side of the job, but if you say yes then theres lots of fat in it for them.

I'd shop around some more (or do the bushes myself).

Cost me $330 in labour to fit coilovers, whiteline front and rear swaybars and a 4 wheel alignment on my 34 :pwned: at a place called signature on the gold coast

ring whiteline for another opinion on the parts costs.

install costs depend on where you take it. $60-75 for a wheel alignment is not uncommon. the amount of labour also depends widely on the specific car and its suspension, some suspension is easy to pull apart some of it you are at it for ages.

labour costs to pull all your suspension apart are always going to be higher than a couple of little bushes.

$75 for a wheel alignment will get you rubbish. They will most likely just do front toe and that's it. A skyline needs a full 4 wheel alignment (front toe, rear toe, rear camber and with your bushes front caster too). This will cost between $140 and $200.

the install prices they quote is not too bad. possibly a bit of fat there to allow for unknown problems.

Yep pedders is a rip. I took my castor rods off myself and pressed the old bushes out my self. Only problem was my press wasn't gustsy enough to push the new ones in. Anyway before work took the rods and bushes in to pedders and said i need these done by 4:00. Got there he still hadn't done them, he proceeded to do a couple other things and then finally got around to it. Took him about 2 minutes... had a whole day and still couldn't manage a 2minute task and still charged me $20.

Go somewhere else don't support these guys, essentially they were charging me $600/hour.

$75 for a wheel alignment will get you rubbish. They will most likely just do front toe and that's it. A skyline needs a full 4 wheel alignment (front toe, rear toe, rear camber and with your bushes front caster too). This will cost between $140 and $200.

the install prices they quote is not too bad. possibly a bit of fat there to allow for unknown problems.

Gah! You get yours done at $140 - $200?

I pay $50 for a FULL alignment.

And it's all this guy does (All he has done for 30+years)

Sets EVERYTHING on my car! Toe, camber, castor. Checks all my bushes, rack etc.

Keeps telling me to rip my HICAS out... LOL

how long does your $50 alignment take?

since I have about 3 alingments or more a year I can tell you there is no way someone could properly align a skyline for $50 and make any money at all. they would be loosing massively. especially if you have adjustable camber and castor (which apparently you do, as do I). I would average the time of 1 wheel alignment guy and the machine at $100 per hour. It takes around 1.5 hours to get it done. (sometimes even double that if there is a lot to do).

even typing out:

front right toe

front left toe

rear right toe

rear left toe

front right camber

front left camber

rear right camber

rear left camber

front right castor

front left castor

traction rod

check

adjust

check (for each of the settings above)

takes up $50 of my time just to type it out! each of those tasks will take around 10 min to get spot on.

how long does your $50 alignment take?

since I have about 3 alingments or more a year I can tell you there is no way someone could properly align a skyline for $50 and make any money at all. they would be loosing massively. especially if you have adjustable camber and castor (which apparently you do, as do I). I would average the time of 1 wheel alignment guy and the machine at $100 per hour. It takes around 1.5 hours to get it done. (sometimes even double that if there is a lot to do).

even typing out:

front right toe

front left toe

rear right toe

rear left toe

front right camber

front left camber

rear right camber

rear left camber

front right castor

front left castor

traction rod

check

adjust

takes up $50 of my time just to type it out! each of those tasks will take around 10 min to get spot on.

Agreed, the only place in melb i have found that does a spot on job including all the big name alignment guys is Ray from resevoir tyre power.... new machine, in depth knowledge on motorsport and willing to spend the 2hrs or so that is needed to set everything up perfectley.

im meant to get charged 85 for wheel alignment because its for 4 wheels but im a good customer and only get charged 45

do half of the stuff yourself, save some cash and learn something....

Coilovers is easy! 3 bolts each strut and they come out! ive never done any suspension work before but ive done all front bushes, coilovers, rear cradle bushes.......

save cash then get wheel alignment!

how long does your $50 alignment take?

since I have about 3 alingments or more a year I can tell you there is no way someone could properly align a skyline for $50 and make any money at all. they would be loosing massively. especially if you have adjustable camber and castor (which apparently you do, as do I). I would average the time of 1 wheel alignment guy and the machine at $100 per hour. It takes around 1.5 hours to get it done. (sometimes even double that if there is a lot to do).

even typing out:

front right toe

front left toe

rear right toe

rear left toe

front right camber

front left camber

rear right camber

rear left camber

front right castor

front left castor

traction rod

check

adjust

check (for each of the settings above)

takes up $50 of my time just to type it out! each of those tasks will take around 10 min to get spot on.

Well you need to take up some typing lessons and go a bit faster, because you are very expensive .

LMAO, Pedders quoted me $750 fat ones for install of coilovers

"yeah mate it will take us all day if were lucky, your kind of car is very difficult to work on" <----- wank

i have a S1 R33 and it took me 5hrs to install and i don't know shit about suspension.

Aif

I dont kno much about it, but what I do know is that anything to do with suspention and breaks is something id like done by a professional. I wouldnt like my wheel falling off or my breaks not working because i forgot to bleed the system fully.

on a hoist at work with a a rattle gun and the right tools, did my coilovers in under 30min, you realy have to consider a real workshop for an import, not your local discount suspension imho. most time they can deff do the job. but wont know what works well for alignment specs on a skyline.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...