Jump to content
SAU Community

Recommended Posts

That what the car stands are for, so u can safely work under them as they wont collapse like a jack can.

theres no real difference in safety with working under a hoist or car stands, they both go under the jacking points of the vehicle

just make sure you jack the car up on level ground and have all the stands equal hights.

I am very concerned with the safety of myself. Dropping my car is my biggest fear. From reading my replies to the trolley jack thread, you can see i don't skimp on safety.

I have 3 big trolley jacks, and 2 small ones.

Normally when I jack the front of the car up, it gets one big trolley jack in the middle of the member, 2 stands on either side of the big jack on the member, and 2 small trolley jacks under various points. I would put the others under there too, but then there's not enough room to work on the car.

If I have the car up on 4, I use 4 stands. I still have one big jack in the middle of the cross member too. I also chuck a big jack under the diff, and I chuck the 2 small jacks to the side. I'll just use the last big jack under something random just for safety, incase if my other 4 stands and 4 jacks fail. hahaha.

aye carumba manwhore!! that made me dizzey!

well i bought my 4 stands and a 2.5t trolley jack so i could do my g/b oil and fit my exhaust myself when i get it too. so i might put it up on all four to see how it looks when i do the g/b oil - if i feel unsafe, i'll bring it down onto two stands. my drive-way is pretty much level....

I certainly wouldn't use only two... four is the magic number!

You really don't EVER want to be under your car while it's being fully or partially supported by a jack.

I know how you feel though... tiny little surface of the stands holding your car up, and it looks dodgy the first few times you do it... but a mate of mine helped me get over it.

Under his car, bracing against the wall, with a breaker bar trying to undo something... whole car shakes around on the stands.. but it doesn't budge. Same thing getting the gearbox out of my car.

So now I do the same.. jack it up, 4 stands, then release the jack a little so it's about 1cm from the diff or whatever you're jacking from, and then give the car a bit of a shove. It won't budge. ;o)

If u are changing the gearbox oil just jack up the front , by time time u jack the back of the car up u could have the oil out

wouldnt jacking the car up on two stands make draining and filling the gearbox oil uneven because the car is tilted

having 4 jacks and 4 stands under your car will restrict the amount of room you have to move around, sounds kinda stupid if u ask me. if your that scared to get under a car which is on 4 car stands then make friends with a mechanic and ask to use their hoist on a sat or weeknight.

if the car is on level ground and the stands are in the right positions then you should not have a problem.

If you are really worried about it get a real spare or even another cars spare and sit that next to you under the car if it manages to fall off the stands spare will give you a chance as the car wont fall so far when changing tyres on the side of a road this is also a good idea as disks can get easily damaged if the car falls of the jack.

4wheel drive wheel or nice wide rims are of course better

having 4 jacks and 4 stands under your car will restrict the amount of room you have to move around, sounds kinda stupid if u ask me. if your that scared to get under a car which is on 4 car stands then make friends with a mechanic and ask to use their hoist on a sat or weeknight.

if the car is on level ground and the stands are in the right positions then you should not have a problem.

I have the equipment, so why not use it?

Let me tell you, if i have the whole car up, 4 jacks and 4 stands hardly takes up much room at all. You're literally talking 1 jack and 1 stand per corner. Plenty of room where it counts.

I have not found room to be of an issue.

I would say yes, it is overkill, stupid no. If I hvae the equipment, why not use it to make it safer (provided it doesn't get in the way - which it doesn't).

I still haven't figured out where to place the stands for the rear of the car. This is on an R32 by the way. I've used a trolley jack on the diff before to change the wheels, but I've never had to work under the rear of the car so I've never lowered it onto stands. Where do you place your stands for the rear of the car?

dont think really good idea to use the diff as the point to jack up the car...there is a centre point just in front of the diff to jack rear up..if car is too low then...drive on couple pavers to bring the car up abit....I did my G/B oil with ramps to the front only, thought about jacking the back up and using stands to level but didnt need too. 4 stands is the go and have a jack or 2 in some key points, pre load it abit, just in case something does happen to the stands the jack/s will take up the weight

yeah 4 stands is pretty dangerous......

seen it fail before....

one good tweak of the wrench and it could be goodnight irene!!!!

best find a mate with a proper hoist, or use just two stands where at least there are two wheels on the gorund to give the car some balance......

you could always just test it by putting it on for stands and just leaning agianst the car :)

dont think really good idea to use the diff as the point to jack up the car...there is a centre point just in front of the diff to jack rear up..if car is too low then...drive on couple pavers to bring the car up abit....I did my G/B oil with ramps to the front only, thought about jacking the back up and using stands to level but didnt need too. 4 stands is the go and have a jack or 2 in some key points, pre load it abit, just in case something does happen to the stands the jack/s will take up the weight

Why isn't it a good idea to use the rear diff? It's been recommended by many people on this forum to use as the rear jacking point. I've had a look at the manual and I just realised the picture shows jacking point is indeed slighty pass the the diff. I've always assumed using the diff was fine. Well it's been ok for me so far.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • When you crank your car, and hit it with a timing light, can you see a steady crank timing?
    • Oh, forgot to add, A few months ago I was getting mixture codes and the car was using crap loads of fuel. You could smell the unburned fuel in the exhaust, it was crazy strong. Economy was over 17.5 l/100 and usually around 19. I smoked the engine and found a leaky CCV hose which I replaced and then I replaced my two pre cat O2 sensors, I also replaced the MAF. This fixed my mixture codes and improved my exonomy but I'm still 14 - 15 l/100 when pottering about town so something is still amiss. Throttle response is much better and it has more pep but I'd like to know why it's still so thirsty (and I'm hoping that whatever it is gives me a bit more poke).    
    • Car is on factory injectors/z32 maf/ q45 throttle body/ z32 ecu with nistune 
    • Hello all, currently finishing up a rb25 swap into my s14. Having issues with starting, car has spark (confirmed by pulling a plug and watching it spark), has fuel(confirmed by checking pulse/voltage at injectors all spark plugs are soaked in fuel). Car cranks over and pops into the exhaust with a heavy fuel smell but no attempt to start or run, I have torn the timing cover off and triple confirmed timing, turned the CAS in multiple spots both directions, attempted to start with coolant temp and maf unplugged, checked my fuel lines and made sure they weren’t backwards, checked voltage at cas/injectors/coilpacks, made sure all the grounds in the harness are connected and added a few grounding straps (1 from chassis to block, 1 from chassis to head, and 1 from chassis to igniter chip) I am getting stumped here. As a last ditch effort I made a full grounding harness tonight that’s going to run from the battery and add an extra ground from the battery onto the coil pack harness/igniter chip/ intake manifold/ Wiring specialties harness ground/ and alternator. I’m hoping maybe the grounding harness will fix it here but posting here to see if anyone has any other ideas on what else I can check. My fuel pressure is unknown right gauge will be here tomorrow.  IMG_3206.mov
    • yeah I was shocked when I checked my spare OEM on and as below that's how they come from Nissan. (side interesting note new NEO gearbox and replacement park lack the brass bush on the tips and its just all alloy) unsure about damage to the box currently back at 1110 to be pulled down/inspected and selector fork replaced as he built it previously and given the never before seen failure on his billet forks he is replacing it under warranty. He said he has used always OEM the keyway tab without issue for years so it could be an unlucky coincidence. I did talk to him about the sharp corners and stress concentration too. Re: hard shifts i got 7+ years out of the OEM one and the fork itself failed not the keyway. so could be bad luck as I said or an age thing + heat cycles in box and during fabrication of billet?
×
×
  • Create New...